Viessmann CM2 500 Скачать руководство пользователя страница 42

Страница: 42 / 50

5773 597 - 04

Vitocrossal 200, CM2 400, 500 and 620 Installation

Component Installation Guide

Flashing and storm collar installation

Flashings and storm collars are field supplied.

Flashings and storm collars suitable for Type B vent

materials (or better) may be used.
To obtain flashings and storm collars, please contact

your local vent material supplier. Follow the installation

instructions supplied by the special venting manufacturer.

Vent Termination Location Requirements - Vertical

WARNING

Vent termination must be at least 12 in. (305 mm)

above the anticipated snow level (consult your local

building authorities or local weather office). Locate

vent termination in such a way that it cannot be

blocked by snow.

IMPORTANT

A vent used in a special venting system with positive

vent pressure and passing through a roof shall extend at

least 18 in. (450 mm) above the highest point where it

passes through the roof and any other obstruction within

a horizontal distance of 18 in. (450 mm).
The special vent system shall not be routed into, through,

or within any other vent such as an existing masonry or

factory-built chimney.

A masonry chimney flue may be used to route the venting

system only if no other appliance is vented in the same flue.

For flat roof applications

The vent must be installed observing local regulations

in addition to National Codes, CAN/CSA-B149.1 or 2

(for installations in Canada) or ANSI-Z223.1 or NFPA 54

(for installations in the U.S.A.).

For sloped roof applications

with distance b greater than 18 in. (450 mm)

For sloped roof applications

with distance b less than 18 in. (450 mm)

a minimum 18 in. (450 mm)

b <18 in. (450 mm)

Venting

Содержание CM2 500



















































Результаты поиска

Содержание CM2 500

Отзывы:

Похожие инструкции для CM2 500

Бренды по названию

Популярные бренды

Viessmann CM2 500, Руководство по установке

Результаты поиска

Содержание CM2 500

Отзывы:

Похожие инструкции для CM2 500

Бренды по названию

Популярные бренды