background image

8

5712 718  v1.0

Vitotronic 100, KW10B  Operating and User’s Information

Diagnostics

Operation 

Failure, cause, correction

o

  Are all controls operating properly (i.e. thermostats,  

 

low water cut-off, etc.)?

o

  Are all wire connections tight and secure?

Symptom/Condition

Cause

Correction

Boiler control is not active

(GREEN power LED is not illuminated)

Power switch “

8

“ is in “

0

“ position

Ensure power switch “

8

“ is in “

I

“ 

position.

Main power to boiler control and 
heating system has not been 
activated

Activate main power; ensure 
120 VAC is supplied to control 
(receptacle).

Fuse on Vitotronic boiler control has 
deactivated heating system

Replace fuse in control with same 
type and rating
(F1: T 6.3 A / 250 V, slow blow).

Burner does not activate, or activates 
intermittently

(RED fault LED flashes)

Burner is not electrically connected

Ensure 7-pole 

fA

 plug-in connection 

to burner and/or power venter is/are 
made.

Fixed high limit (FHL) tripped

Reset FHL by pushing in the pin, 
labelled with a “

E

“ (using a 

ballpoint pen).
If a “click” can be heard, the limit 
was tripped.

No fuel 

*

1

with oil:

 Ensure sufficient supply of oil

with gas:

 Open main gas supply valve 

or
contact your local gas utility

Pumps on continuously

F1 fuse blown

Replace fuse

Burner does not activate

Control calls for heat but burner does 
not respond 

*

1

Attempt to reset burner using reset 
button on the burner
(underneath burner hood).

Service burner if necessary.
Refer to troubleshooting section in 
burner manual.

Control calls for heat but burner does 
not respond

Power venter has to have separate 
120 VAC power supply to motor (see 
power venter instructions).
Refer to troubleshooting section in 
power venter manual. Air proving 
switch, blower wheel or timer/relay 
inside power vent may be defective.

Other accessory defect

Ensure proper operation of all 
accessories; replace if necessary. 
Refer to technical literature supplied 
with accessories.

F1 fuse blown

Replace fuse

Continuous burner call

F3 Fuse blown

Replace fuse

Override switch on

Turn off override

*

1

  Red LED does not flash when Honeywell S8600 ignition control module is used with boiler.

Содержание 7834 238













Отзывы: