Videx Art.2270 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 44

Videx Art.2270 Скачать руководство пользователя страница 9

66251225-EN - V1.0 - 08/01/18

- 9 -

VX2200 GSM Interface Module - Technical Manual

GSM Interface Module for the VX2200 Digital System

TERMINAL CONNECTIONS

Terminal

Description

NO1

Normally open 1 relay contact.

Relay 1, 2 and 3 contacts:

3A@24Vdc

3A@120Vac

CO1

Common 1 relay contact.

NC1

Normally closed 1 relay contact.

NO2

Normally open 2 relay contact.

CO2

Common 2 relay contact.

NC2

Normally closed 2 relay contact.

NO3

Normally open 3 relay contact.

CO3

Common 3 relay contact.

NC3

Normally closed 3 relay contact.

+

+12Vdc power input (500mA max.)

–

0V ground power.

A1

Auxiliary 1 input (triggers relay 1 when A1 mode set to 000, switched 0V, default).

A2

Auxiliary 2 input (triggers relay 2 when A2 mode set to 000, switched 0V, default).

A3

Auxiliary 3 input (triggers relay 3 when A3 mode set to 000, switched 0V, default).

A

RS485 bus connection (for ease of programming and permanent connection for monitoring purposes).

B

GND

L

BUS line data input.

–

BUS line ground input.

STATUS INDICATION LED’S

LED

Description

During ‘power up’ the red LED (LED1) will flash continuously while trying to connect the Art.2270
module to the network. As soon as the module is connected to the network it will switch OFF. The
LED will also switch ON whenever the line is in use or the module is busy and will flash whenever the
network connection is lost and is trying to re-establish a connection.

The green LED (LED2) will flash whenever it sees data on the

L

and

-

bus connection (when the Art.2270

module is in use). The LED will switch ON and stay ON during communication via the USB or RS485 bus
connection. In standby when the module is not in use the LED will be switched OFF.

TECHNICAL SPECIFICATION

Working Voltage

: 12Vdc +/- 10%

Standby Current

: approx. 60mA

Max. Current

: approx. 500mA (max.)

Phone ID’s (call buttons)

: 1 up to 180 (max.)

Telephone Numbers per ID

: 4 telephone numbers (1 primary, 3 diverts)

Dial to Open Numbers

: up to 1000 per relay (max.), 3000 DTO numbers in total

Status Indication LED’s

: 2 (red LED1 power up/busy, green LED2 data)

Programming

: SMS messaging or PC software

Auxiliary Inputs

: 3 (A1, A2 and A3 switched 0V input)

Dry Contact Relay

: 3 (relay 1, 2 and 3), 3A @ 24Vdc, 3A @ 120Vac

Event Log

: up to 8000 events

USB Port

: micro USB

RS485 Bus Connection

: A, B and GND

Timebands

: 1 programmable timeband

Dimensions

: 157.5mm (W) x 85mm (L) x 65mm (D)

Working Temp.

: -10 +50

o

C

Technical Information

«
...
7
8
9
10
11
...
»

Содержание Art.2270













































Отзывы:

Нет отзывов