Videx Art.2270 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 44

Videx Art.2270 Скачать руководство пользователя страница 8

66251225-EN - V1.0 - 08/01/18

- 8 -

VX2200 GSM Interface Module - Technical Manual

GSM Interface Module for the VX2200 Digital System

Technical Information

ART. 2270 MODULE

VIDEX

R.1.0

VERMD1.1.0

VIDEX

R.1.0

Antenna connection

side view

157.5mm

65mm

85mm

Fig. 3

MODULE VOLUME ADJUSTMENT POTS (VR1 & VR2)

There are 2 volume adjustment POT’s located on the top right side of the Art.2270 module, see

Fig.3

. The

VR1

POT control can

be used to adjust the speech volume towards the door panel (panel’s speaker) and the

VR2

POT control can be used to adjust

the speech volume towards the telephone line (panel’s microphone). Additionally, the volume can also be adjusted during a call
electronically via the telephone keypad (refer to user command table 1 on page 35).

By default both the

VR1

and

VR2

adjustment POTs are set to approximately halfway,

see

Fig.4

.

Speaker Volume Adjustment (speech from phone to panel) -

to increase the speaker

volume turn the

VR1

POT clockwise (up) and to decrease the speaker volume turn the

VR1

POT anti-clockwise (down).

Microphone Volume Adjustment (speech from panel to phone) -

to increase the

microphone volume turn the

VR2

POT clockwise (up) and to decrease the microphone

volume turn the

VR2

POT anti-clockwise (down).

VR1

VR2

DOWN

UP

DOWN

UP

Fig. 4

USB CONNECTION

The micro-USB connection allows the Art.2270 module to be connected to a laptop/PC for ease of programming (refer to page 18
for connecting the GSM module to a laptop/PC). Further information on programming using the GSMSK PC software can be found
in the following manual:

GSMSK_66251720_EN_V1-3

(or later version).

Status indication LED's

Power terminal connections

Auxiliary terminal connections

RS485 bus connection

Databus terminal connections

Relay terminal
connections

Antenna connection

SIM card holder

VR1 & VR2 speech
volume control POT’s

Micro USB connection

«
...
6
7
8
9
10
...
»

Содержание Art.2270













































Отзывы:

Нет отзывов