Videx 380N/UK Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 28

Videx 380N/UK Скачать руководство пользователя страница 2

66250010-EN - V2.0 - 24/09/18

THE POWER TO SECURE

- 2 -

Art. 380N/UK Telephone Interface Module - Installation Instructions

Telephone Interface Module

APPROVAL

The equipment has been approved in accordance with Council Decision

98/482/EC

for pan-European single terminal connection

to the public switched telephone network (

PSTN

). However, due to differences between the individual PSTNs provided in different

countries, the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network

termination point. In the event of problems, you should contact your equipment supplier.

The

Art.380N/UK

telephone interface is fully approved to be connected to the following circuits:

• Public Switched Telephone Network (

PSTN

) - non DDI.

• Private Branch Exchange (

PBX

) or Private Automatic Branch Exchange (

PABX

).

If the unit is to be used on any other network that is not listed above, you must first contact the vendor.

The

Art.380N/UK

telephone interface complies fully, in all modes of operation, with the requirements of the European Standard:

ETSI ES 203 021-3, V2.1.2 (2006-01): Access and Terminals (AT); Harmonized basic attachment requirements for Terminals for

connection to analogue interfaces of the Telephone Networks.

MANUFACTURER

All Countries:

VIDEX ELECTRONICS S.P.A.

www.videx.it - [email protected]

Tel: +39 0734-631699 - Fax: +39 0734-632475

The product is CE marked demonstrating its conformity and is for distribution
within all member states of the EU with no restrictions. This product follows
the provisions of the European Directives 2014/30/EU (EMC); 2014/35/EU
(LVD); 2011/65/EU (RoHS): CE marking 93/68/EEC.

UK Customers:

VIDEX SECURITY LTD.

www.videxuk.com - [email protected]

Tech Line: 0191 224 3174 - Fax: 0191 224 1559

CUSTOMER SUPPORT

VIDEX ELECTRONICS S.P.A.

Via del Lavoro, 1 - 63846 Monte Gilberto (FM) Italy

Tel: (+39) 0734-631699 - Fax: (+39) 0734-632475

www.videx.it - [email protected]

Declaration of Approval

«
1
2
3
4
...
»

Содержание 380N/UK





























Отзывы:

Нет отзывов