Videofied XTO Series Скачать руководство пользователя страница 11

11

INSTALLATION MANUAL

3.

XTO-IP

 

PANEL PROGRAMMING

XTO-IP 

Alarm panel

SERVER

ADDRESSES ?

The

 IP1 address

,

 

Domain name 1

 and/or 

Port 1

 are provided by the monitoring station.

 

Leave Port details at 888 unless otherwise instructed.

 

Press 

OK

 or 

YES

 to enter/modify the parameter then 

OK

 or 

YES

 for validation.

WARNING : You will use either an 

IP address

 or a 

Domain name 

but

 not both

, leave the

 

Domain name

 blank if an 

IP address

 has already been entered.

Press on the right arrow to configure IP/Domain name 2 and PORT2 (for the back-up server), 

and IP/Domain name TMT and PORT TMT (to configure remote maintenance server).

ESC

NO

OK 

or 

YES

ESC

NO

STRATEGY:

ETH+2G3G

4G

2G3G

4G

 

PARAMETERS ?

ESC

NO

OK 

or 

YES

TEST IN PROGRESS

END = OK/YES

2G3G

4G

 LEVEL

5/5

2G3G

4G

 LEVEL ?

2G3G

4G

 LEVEL ?

OK 

or 

YES

The 

APN Code

 (Access Point Name), 

User Name

 and 

Password

 are supplied by the 

mobile operator. Please make sure you have entered the code exactly as indicated by your 

local SIM card operator.

Press 

OK

 or 

YES

 to enter/modify the parameter then 

OK

 or 

YES

 for validation.

Note: When entering your SIM card settings, both APN codes, username and 
password fields are case sensitive! It makes a difference between UPPER and lower 
case letters.

To switch between UPPER and lower case, use the M/m key from CMA keypad or hold a digit key 

(0-9) for XMA/XMB.

Once the 2G3G

4G

 test completed, the keypad will display one of the following results :

-  A level between 0/5 and 5/5.

-  A GPRS Error code (please see Chapter 7 : 2G3G

4

G

 errors codes and contact your 

technical support). 

If the screens shuts down, press any key to light it up except 

OK

 or 

YES

ESC NO

 or 

CLR

.

The 2G3G

4G 

level test can last several minutes.  Do not interrupt the test or remove the SIM 

card during the test.

IMPORTANT : Videofied will require a 3/5 grade or better for reliable transmission 
of Video alarms.

ESC

NO

2G3G

4G 

PARAMETERS ?

OK 

or 

YES

How the alarms and videos are transmitted to the monitoring station ?

ETH+2G3G

4G

 : Ethernet transmission with GPRS backup.

2G3G

4G

 : GPRS transmission only (if the Ethernet connection is not used).

ETH : Ethernet transmission only (only if GPRS is not used).

Warning : the transmission mode “Ethernet only” is not recommended.

ESC

NO

IP1 ADDRESS 

0.0.0.0

DOMAIN NAME 1

PORT 1

888

APN CODE

internet-entrepr

USER NAME

orange

PASSWORD

orange

Содержание XTO Series




























Отзывы: