Playing 3D Contents
At this point, 3D-Theatre is connected to the player and your display.
When the player and the display are powered, POWER light is ON (GREEN)
Upon successful connection between the player and the converter, LINK lights up ON (GREEN)
The emitter lights – 2 lights – are ON (GREEN)
Turn the glasses on by gently pressing ON button (on the glasses)
All three lights on the converter light up GREEN
Initially, some flickering is experienced – left/right lens turning on & off – until emitter syncs with the glasses
When locked, if the picture is still not clear, press the left button on the emitter - as you are facing the emitter – to adjust the sync
frequency. There are 2 different settings and by pressing and releasing the button, one can select the desired picture settings
If experiencing distorted 3D images – background & foreground blended – press the right button on the emitter for a few seconds –
releasing will change the light from green to RED – to adjust the polarity setting. The image should correct itself
When playing Side-by-Side (SBS) contents, press P1 button next to the Dip Switch box once.
When playing Top/Bottom or Over/Under contents, press P1 button twice.
You may press P1 button multiple times until the picture is displayed in the right order
Troubleshooting
If experiencing no picture – NO SIGNAL – after the above installation, try the following:
1-
If using PS3 as a player, go to the settings and select VIDEO SETTINGS and go down the menu until you see “BD… 1080 24Hz …
Automatic”. Change that to OFF
2-
If using PS3 as a player, go to the DISPLAY SETTINGS and select HDMI and Automatic to configure the player to work with the 3D
contents. Make sure the converter is connected when going through the settings
3-
If you get “NO SIGNAL”, “UNSUPPORTED SIGNAL’’ or a similar message, make sure your USB cable is connected to the wall
connector with 5V power. Converter may not be getting enough power via USB connected to the other device
4-
If you get messages similar to the ones in Point #2, check to make sure your Television is set to the right HDMI connection by
going to MENU on the TV, selecting INPUT and selecting the right HDMI connection # - check the # where you inserted the
HMDI cable in the TV
5-
For best quality picture, go to the MENU on TV screen, select PICTURE and go to the mode and switch between STANDARD,
CUSTOM, GAME, SPORT, CINEMA, EXPERT (options vary between different televisions)
6-
You are getting no signal message and your box is connected to a display at 120Hz. Change Dip Switch #1 to down position,
remove USB cable from the back of the box, plug it back in after 5 seconds and see if you get the picture. If you do, the
television is not true 120Hz and operates at 60Hz (regardless of marketing material/product specifications)
7-
All Three lights are not ON, your connections are bad. Unplug all cables and reconnect them.
8-
Only POWER light is ON, unplug and re-plug HMDI cables from both devices and the convertor
9-
3D light is not ON, check to make sure you have 3D contents
10-
Emitter lights are not on, unplug and plug 3-pin DIN connector
Supported Modes:
720p60 Frame packing, Side-by-Side, Top-and-Bottom
720p50 Frame packing, Side-by-Side, Top-and-Bottom
720p24 Frame packing, Side-by-Side, Top-and-Bottom
720p25 Frame packing, Side-by-Side, Top-and-Bottom
720p30 Frame packing, Side-by-Side, Top-and-Bottom
1080i60 Side-by-Side
1080i50 Side-by-Side
1080p24 Frame packing, Side-by-Side, Top-and-Bottom
1080p25 Frame packing, Side-by-Side, Top-and-Bottom
1080p30 Frame packing, Side-by-Side, Top-and-Bottom
