vidaXL 50762, Руководство по эксплуатации и технике безопасности

Страница: 27 / 376

27 EN___User manual |
or decommissioning, it is recommended good practice that all
refrigerants are removed safely.
When transferring refrigerant into cylinders, ensure that only
appropriate refrigerant recovery cylinders are employed.
Ensure that the correct number of cylinders for holding the
total system charge are available. All cylinders to be used are
designated for the recovered refrigerant and labelled for that
refrigerant (i.e. special cylinders for the recovery of refrigerant).
Cylinders shall be complete with pressure-relief valve and
associated shut-off valves in good working order. Empty
recovery cylinders are evacuated and, if possible, cooled before
recovery occurs.
The recovery equipment shall be in good working order with a
set of instructions concerning the equipment that is at hand
and shall be suitable for the recovery of all appropriate
refrigerants including, when applicable, flammable refrigerants.
In addition, a set of calibrated weighing scales shall be available
and in good working order. Hoses shall be complete with leak-
free disconnect couplings and in good condition. Before using
the recovery machine, check that it is in satisfactory working
order, has been properly maintained and that any associated
electrical components are sealed to prevent ignition in the
event of a refrigerant release. Consult manufacturer if in doubt.
The recovered refrigerant shall be returned to the refrigerant
supplier in the correct recovery cylinder, and the relevant waste
transfer note arranged. Do not mix refrigerants in recovery
units and especially not in cylinders.
If compressors or compressor oils are to be removed, ensure
that they have been evacuated to an acceptable level to make
certain that flammable refrigerant does not remain within the
lubricant. The evacuation process shall be carried out prior to
returning the compressor to the suppliers. Only electric heating
to the compressor body shall be employed to accelerate this
process. When oil is drained from a system, it shall be carried
out safely.
7.4 Exception Clauses
The manufacturer will bear no responsibilities when personal
injury or property loss is caused due to the following reasons.
1. Damage the product due to improper use or misuse of the
product.
2. Alter, change, maintain or use the product with other
equipment without following the instructions manual.
3. After verification, the defect of the product is directly
caused by corrosive gas.
4. After verification, defects caused due to improper operation
during transportation of the product.
5. Operate, repair, maintain the unit without following the
instructions manual or related regulations.
6. After verification, the problem or dispute caused due to
using the parts and components produced by other
manufacturers.
7. The damage caused due to the natural calamities, bad using
environment or unforeseeable circumstances.
8 Maintenance and cleaning
6
Warning
• Before cleaning the air conditioner, please turn off the unit
and disconnect power. Otherwise, it may cause electric
shock.
• Do not wash air conditioner with water. Otherwise, it may
cause electric shock.
• Do not use volatile liquid (such as thinner or gas) to clean
the air conditioner. Otherwise, it may damage the
appearance of air conditioner.
8.1 Clean outer case and grille
See image 48
• Clean outer case: If there's dust on the surface of outer
case, please use soft towel to wipe it. If the outer case is
very dirty (such as grease), please use neutral abluent to
wipe it.
• Clean grille: Use cleaner or soft brush to clean it.
8.2 Clean filter
1. Remove the filter
See image 49
2. Clean filter
Use cleaner or water to clean the filter. If the filter is very dirty
such as grease, use warm water 40°C mild detergent to clean it
and then allow it dry.
See image 50
3. Install filter
After the filter is cleaned and dried, reinstall it well.
• The filter should be cleaned about once every three
months. If there's much dust in the operation environment,
you can increase clean frequency.
• Do not dry the filter fire or hair drier. Otherwise, it may be
deformed or catch fire.
8.3 Clean heat discharge pipe
Remove the heat discharge pipe from air conditioner, clean and
dry it , and then reinstall it. (For the method of installation and
removal , please refer to the instruction for "Installation and
disassembly of heat discharge pipe").
8.4 Checking before use-season
• Check whether air inlets and air outlets are blocked.
• Check whether plug and socket are in good condition.
• Check whether filter is clean.
• Check whether batteries are installed in remote controller.
• Check whether joint, window bracket and heat discharge
pipe are installed tightly.