FCC STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
CALIFORNIA PROP 65 WARNING
WARNING:
This product can expose you to chemicals including lead,
which is known to the State of California to cause cancer.
For more information go to www.P65Warnings.ca.gov.
WARRANTY
Victrola is a registered trademark of Innovative Technology Electronics LLC.
Innovative Technology Electronics LLC.
Limited Warranty: 90 Days Labor, One Year Parts
Innovative Technology Electronics LLC. (IT) warrants the product to be free from “Defects” in
materials under normal use for a period of “One Year” from the date of the original purchase. The
Warranty is “Not” transferable. IT agrees, within the initial “90 Day” period, to repair or replace the
product if it is determined to be defective at “No Charge”. It is further agreed that IT will cover the
cost to repair or replace damaged “Parts” only for a total period of “One Year” from the date of the
original purchase. The warranty does not cover cosmetic damage, antennas, AC cords, cabinets,
headbands, ear-pads, or damage due to line power surges, connection to improper voltage supply
or settings, misuse, mishandling, accident, acts of God or attempted repair by an unauthorized
service agent.
AUTO RETURN RESET
It is recommended to reset the Auto Return when you move this product.
The mechanism of Auto Return will rotate irregularly when moving and it will cause
the malfunction of Auto Return. The following steps will reset the Auto Return.
1. Place a record on the platter and play it (Follow the Operation Steps above).
2. Manually place the Tone Arm to the blank part at the end of the record
and let it finish playing.
3. The mechanism of Auto Return function will adjust itself properly,
then the tone arm will automatically return to the arm rest.
HOW TO REPLACE THE TURNTABLE NEEDLE (Replacement Needle # ITNP-LD1)
Removing the Stylus from the Cartridge
1. Set a screwdriver at the tip of the stylus
and push down to the direction “A”.
WARNING: When applying force to stylus,
too much may damage or break the stylus.
2. Pull the stylus out toward the direction “B”.
Installing the Stylus
1. Hold the tip of the stylus and insert the other
edge by pressing toward direction “C”.
2. Push the stylus up toward direction “D”
until it locks at the tip.
Caution:
� Do not remove or bend the stylus needle.
� Do not touch the needle to avoid injury to your hand.
� Turn off the unit’s power before you replace the stylus.
� Keep out of reach of children.
Please note: The stylus should last about 300 hours under
normal use. It is recommended that the stylus be replaced
as soon as you notice a change in sound quality.
Made In China.
ASSEMBLY OF THE DUST COVER
1. Remove protective plastic film from
the DUST COVER.
2. Align the DUST COVER (#12) to the DUST
COVER HINGES (#11), on the back of the unit.
Then, push down the dust cover gently
to clip into the hinges.
TURNTABLE OPERATION
SET UP
An AC/DC adaptor with an output of 12V/1.0A is included with the USB Turntable.
This adaptor is required for operating the unit.
1. Connect the external Hi-Fi Amplifier or Speaker System using RCA Cables (Not
Included). NOTE: The RCA Cables are color coded, the red cable is plugged into
a red jack on both the unit and external device (white cable into the white jacks).
2. Firmly and securely insert the DC plug of the adaptor to the DC IN Jack on the
back of the unit.
3. Plug the adaptor’s AC plugs into a power outlet rated at 120V AC ~ 60Hz.
BASIC OPERATION
Before use, be sure to remove the white stylus guard off of the needle. Always
make sure that the tone arm is unlocked and free to move across the record while
operating. Lock the tone arm in place again when it is not in use.
1. Push the POWER Button on the unit to turn the turntable ON.
2. Place a record on the TURNTABLE PLATTER and select the desired speed
(33 1/3 / 45) by pushing the SPEED SELECTION SWITCH to the speed
according to the type of record.
NOTE: When playing a 45 rpm record, use the included 45 rpm adaptor located
inside the accessories bag.
3. Press the START / STOP Button to Start the Turntable. Pushing this button again
will Stop (Pause) the Record.
4. Open the TONE ARM CLIP to release the TONE ARM. Push the TONE ARM LIFT
LEVER Button ( ) to raise the arm. Gently move the tone arm to the desired
position over the record. The turntable will begin to spin only when the tone arm
is moved toward the record. To begin playing, push the LIFT LEVER Button again
to lower the arm slowly onto the desired position of the record.
5. To return the Tone Arm at any time press and hold (for 1-2 seconds) the RETURN
Button. This will automatically return the Tone Arm to the Tone Arm Holder and
will Automatically stop the record from playing.
PLEASE NOTE: The Auto Return will automatically return the Tone Arm to the
Holder once it has reached the end of the record.
6. To select the volume level, use your external device to adjust the volume.
9
To obtain service, the purchaser MUST present an original sales receipt / proof of purchase.
Please contact us at www.victrola.com to request an RMA (Return Material Authorization)
number to return products for service or replacement. Returns without an RMA number on the
package will be refused and returned to sender. Upon receipt of the returning item and our full
inspection (IT) may issue a replacement to customer for the same item or of one that has equivalent
value and features. To return an item, supply full name, return address, phone number, item
purchased, receipt of purchase and reason for return to obtain RMA number.
All returns must be in the original packaging or reasonable substitute to prevent damage. Customer
“Must” include full name, shipping address and telephone number inside of package. No return will
be shipped back to a PO Box or APO address.
Please include your check or money order in the amount of:
• USD $5.00 for items $10.00 to $39.99 (Price Paid Per Unit)
• USD $10.00 for items $40.00 to $99.99 (Price Paid Per Unit)
• USD $16.00 for items $100.00 and up (Price Paid Per Unit)
• Shipping fees are non-refundable
to be payable to Innovative Technology Electronics LLC. (for handling and return shipping charges)
(IT) will not be responsible for delays or unprocessed claims resulting from a purchaser’s failure to
provide any / all of the necessary information. Send all inquiries or RMA request via our website
www.victrola.com/pages/technical-support.
Innovative Technology Electronics LLC.
1 Channel Drive
Port Washington, NY 11050
Toll free: 1-877-483-2497
Website for support: www.victrola.com/pages/technical-support
There are no express warranties except as listed above.
REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY
OF THE CUSTOMER, (IT) SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL
DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT
EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW. ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED
IN DURATION TO THE DURATION OF THIS WARRANTY.
Some states do not allow the exclusion or limitation of incidental or consequential damages, or
limitations on how long an implied warranty lasts, so the above exclusions or limitations may not
apply to you. This warranty gives you specific legal rights and you may also have other rights, which
vary from state to state.
IF THE BELT BECOMES LOOSE
The belt and turntable platter have been installed properly during production, but
the belt may have become loose during transportation. If so, follow the below
procedures to re install the belt drive:
1. Remove the rubber mat from the turntable platter and carefully unclip the small
E ring from the turntable shaft (using tweezers or pliers), Then release the
turntable platter from the shaft.
2. Put the drive belt on the inner rim of the turntable platter and pull it through the
hole on the platter as shown in the drawing.
3. Hold the belt with your fingers and place the belt onto the motor pulley as shown
in the drawing.
4. Clip the E ring on the shaft and place the rubber mat onto the turntable platter.
Caution: Make sure that the drive belt is not twisted or distorted. Avoid oil. Oil
splashes will make the belt slippery.
TIPS FOR BETTER TURNTABLE USE
1. When opening or closing the turntable cover, handle it gently, gripping it either at
the center or at each side.
2. Do not touch the needle tip with your fingers; avoid bumping the needle against
the turntable platter or record edge.
3. Frequently clean the needle tip, using a soft brush in a “back-to-front’ motion.
4. If you must use a needle cleaning fluid, use very sparingly.
5. Gently wipe the dust cover and turntable housing with a soft cloth. Use only a
small amount of mild detergent to clean the turntable and dust cover.
6. Never apply harsh chemicals or solvents to any part of the turntable system.
USB RECORDING OPERATION
To properly record your vinyl to MP3 via computer, use the included USB Output
Cable and Instructional CD Software. Connect one end of the USB cable to the
turntable and the other end into your computer. Then connect the AC power cord to
the turntable. To install and use the software on your computer, select the proper
Mac or PC install files, then follow the prompts provided on the Instructional CD.
For the most up to date manuals, software, instructional details, troubleshooting
or other downloadable content, please go to http://audacityteam.org.
