Victor cutmaster 82 Скачать руководство пользователя страница 23

Страница: 23 / 80

CUTMASTER 82

Manual 0-4979

INSTALLATION

3-1

SECTION 3 SYSTEM:

INSTALLATION

3.01 Unpacking

1. Use the packing lists to identify and account for

each item.

2. Inspect each item for possible shipping damage.

If damage is evident, contact your distributor and

/ or shipping company before proceeding with

the installation.

3. Record Power Supply and Torch model and serial

numbers, purchase date and vendor name, in the

information block at the front of this manual.

3.02 Lifting Options

The Power Supply includes a handle for hand lifting

only. Be sure unit is lifted and transported safely and

securely.

WARNING

Do not touch live electrical parts.
Disconnect input power cord before moving

unit.

FALLING EQUIPMENT

can cause serious personal

injury and can damage equipment.

HANDLE

is not for mechanical lifting.

• Only persons of adequate physical strength should

lift the unit.

• Lift unit by the handles, using two hands. Do not

use straps for lifting.

• Use optional cart or similar device of adequate

capacity to move unit.

• Place unit on a proper skid and secure in place

before transporting with a fork lift or other vehicle.

3.03 Opening the Contactor Cover

The input power cord is connected to the main contactor,

the contactor is located inside a box with a snap on cover.

The cover is held in place with two or more snap lock

tabs. To remove the cover release the front latch and tilt

the cover up about ½ inch. Then squeeze both sides of

the cover and lift it straight up. See the Primary Input

Power Connections section for the necessary changes to

the Contactor. Remember to replace the Contactor Cover

when the changes are complete.

Art# A-11478

Contactor cover

3.04 Primary Input Power Connections

CAUTION

Check your power source for correct voltage

before plugging in or connecting the unit.

Check the Voltage Selector at the rear of the

unit for correct setting before plugging in

or connecting the unit. The primary power

source, fuse, and any extension cords used

must conform to local electrical code and the

recommended circuit protection and wiring

requirements as specified in Section 2.

Most units are shipped from the factory with a 230 Volt

input power cable wired to the input contactor in the

single - phase configuration. The following illustrations

and directions are for changing that configuration to a

different voltage and or to three - phase operation or

back again if a change had already been made.

Art # A-07984_AB

Single-Phase (1ø) and Jumper Settings

L3
L4

Jumper L1 -L4

Jumper

L2-L3

L1
L2
L3

GND

Single Phase Input Power Wiring

Art # A-07983_AB

Three-Phase (3ø) and Jumper Settings

L3
L4

Jumper L1 -L4

L1
L2
L3

GND

Store copper jumper in spare parts box

Three Phase Input Power Wiring

Содержание cutmaster 82

















































































Результаты поиска

Содержание cutmaster 82

Отзывы:

Victor cutmaster 82, Руководство по эксплуатации, Страница: 23 / 80

Результаты поиска

Содержание cutmaster 82

Отзывы: