Victaulic RG3212 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 28

Victaulic RG3212 Скачать руководство пользователя страница 5

DANGER

1. Avoid using the tool in potentially

dangerous environments.

Do not expose

the tool to rain, and do not use the tool in
damp or wet locations . Do not use the tool
on sloped or uneven surfaces . Keep the
work area well lit . Allow sufficient space to
operate the tool properly .

2. Ground the motor to protect the operator

from electric shock.

Ensure that the motor

is connected to an internally grounded
electrical source .

3. Disconnect the power cord from the

electrical source before servicing the
tool.

Only authorized personnel should

perform maintenance on the tool . Always
disconnect the power cord from the
electrical source before servicing or
adjusting the tool .

4. Prevent accidental startups.

Place the

power switch in the “OFF” position before
connecting the tool to an electrical source .

WARNING

1. Prevent back injury.

DO NOT attempt to

lift tool components without the use of
mechanical lifting equipment .

2. Wear proper apparel.

Do not wear loose

clothing, jewelry, or anything that can
become entangled in moving parts .

3. Wear protective items when working with

tools.

Always wear safety glasses, hard hat,

foot protection, and hearing protection .

4. Keep hands and tools away from grooving

rolls and stabilizer wheel during the
grooving operation.

Grooving rolls can

crush or cut fingers and hands .

5. Do not reach inside pipe ends during tool

operation.

Pipe edges can be sharp and

can snag gloves, hands, and shirt sleeves .
Never reach across moving parts .

6. Do not over-reach.

Maintain proper footing

and balance at all times .

CAUTION

1. This tool is designed ONLY for

roll grooving pipe sizes, materials, and
wall thicknesses listed in the “Tool
Ratings for Steel Pipe” section.

2. Inspect the equipment.

Before using the

tool, check all moveable parts for any
obstructions . Verify that tool components
are installed and adjusted in accordance
with the “Tool Setup” section .

3. Stay alert.

Do not operate the tool if you are

drowsy from medication or fatigue .

4. Keep visitors, trainees, and observers

away from the immediate work area.

All

visitors should be kept a safe distance from
the equipment at all times .

5. Keep work areas clean.

Keep the

work area around the tool clear of any
obstructions that could limit movement of
the operator . Clean up any spills .

6. Secure the work, machine, and

accessories.

Ensure that the tool is stable .

Refer to the “Tool Setup” section .

7. Support the work.

Support long pipe/tubing

lengths with a pipe stand, in accordance
with the “Long Pipe Lengths” section .

8. Do not force the tool.

Do not force the tool

or accessories to perform any functions
beyond the capabilities described in these
instructions . Do not overload the tool .

9. Maintain tool with care.

Keep the tool

clean at all times to ensure proper and
safe performance . Follow the instructions
for lubricating tool components .

10. Use only Victaulic replacement parts

and accessories.

Use of any other parts

may result in a voided warranty, improper
operation, and hazardous situations .

11. Do not remove any labels from the tool.

Replace any damaged or worn labels .

5

REV_B

TM-RG3212

/ Operating and Maintenance Instructions Manual

«
...
3
4
5
6
7
...
»

Содержание RG3212





























Отзывы:

Нет отзывов