Victaulic 746-LPA Series Скачать руководство пользователя страница 8

TROUBLESHOOTING – SERIES 746-LPA DRY ACCELERATOR

PROBLEM

POSSIBLE CAUSE

SOLUTION

The valve operates without sprinkler activation.

There is a loss of air pressure in the lower inlet chamber of the Series 
746-LPA Dry Accelerator.

Check for air loss at the lower chamber seal. If a leak is present, turn 
the adjustment nut counterclockwise to seal.

Check for any leaks in the system and trim. Confi rm that the air 
maintenance trim assembly (AMTA) is operating properly.

The Series 746-LPA Dry Accelerator does not operate within a 
5-psi/34-kPa pressure drop in system air pressure.

There is a loss of air pressure in the upper air chamber of the Series 
746-LPA Dry Accelerator.

Apply soapy water to all joints around the Series 746-LPA Dry 
Accelerator to check for leaks. Repair any leaks and re-test.

The air decay rate of the system is too slow.

Make sure there are no restrictions in the remote system test valve 
(inspector’s test connection).

If the above procedures do not work, contact Victaulic.

The Series 746-LPA Dry Accelerator does not set up properly 
(cannot get pressure on the upper gauge, and the button pops up 
immediately when pressure is introduced).

The Series 746-LPA Dry Accelerator is installed upside-down.

Remove the Series 746-LPA Dry Accelerator from the trim, and 
turn the unit around so that the vent seal “button” is facing down 
(toward the actuator).

WCAS-6TMG37

I-746.LPA

Series 746-LPA

INSTRUCTIONS FOR INSTALLING AND REPAIRING SERIES 746-LPA DRY ACCELERATORS

I-746.LPA

INSTALLATION AND REPAIR KIT INSTRUCTIONS

UPDATED 10/2006
I-746.LPA     4603 REV A     Z000746LPA

VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2006 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.

US & WORLD HEADQUARTERS

P.O. Box 31
Easton, PA 18044-0031 USA

4901 Kesslersville Road
Easton, PA 18040 USA

1-800-PICK-VIC (1-800-742-5842)
1-610-559-3300
1-610-250-8817 (fax)
[email protected]

CANADA

905-884-7444
905-884-9774 (fax)
[email protected]

EUROPE

32-9-381-15-00
32-9-380-44-38 (fax)
[email protected]

UNITED KINGDOM

44 (0) 1438741100
44 (0) 1438313883 (fax)
[email protected]

CENTRAL AND SOUTH AMERICA

1-610-559-3300
1-610-559-3608 (fax)
[email protected]

ASIA PACIFIC

86-21-54253300
86-21-54253671 (fax)
[email protected]

MIDDLE EAST

971-4-883-88-70
971-4-883-88-60 (fax)

www.victaulic.com

Содержание 746-LPA Series









Отзывы: