background image

13 | 

028-0324-02_LIT-VZ7656F_B-E01_EN 

www.viconics.com

 

 

October 2019

 

Outdoor air temperature 

  Outdoor air temperature display is only enabled when outdoor air temperature sensor is 

connected. 

 

A maximum range status display of 50 °C (122 °F) indicates a shorted sensor. 

Associated functions, such as mode lockouts and economizer function are 

automatically disabled.

 

 

A minimum range status -40 °C (-40 °F) is not displayed and indicates a opened 

sensor or a sensor not connected. Associated functions, such as mode lockouts and 

economizer function are automatically disabled.

 

 

Alarms 

 

If alarms are detected, they will automatically be displayed at the end of the status 

display scroll.

 

 

During an alarm message display, the back lit screen will light up at the same time as 

the message and shut off during the rest of the status display.

 

 

Two alarms maximum can appear at any given time.

 

 

The priority for the alarms is as follows:

 

 

Sequence of manual-scroll status display: 

Manual scroll of each menu item is achieved by pressing the Yes (scroll) key repetitively. The 

last item viewed will be shown on the display for 30 seconds before returning to automatic 

scrolling. Temperature is automatically updated when scrolling is held. 

 

Clock Status

 

 

System 

Mode

 

 

Schedule 

Status

 

 

Outdoor 

Temperature

 

 

Alarms 

(if detected)

 

 

 

 

 

 

 

 

 

 

Monday 

 

Sys Mode 

 

Occupied 

 

Outdoor 

 

Service 

12:00 AM 

 

Off 

 

 

 

xx.x °C or °F 

 

DAS Alrm 

 

 

Sys Mode 

 

Unoccupied 

 

 

 

SetClock 

 

 

Auto 

 

 

 

 

 

Filter 

 

 

Sys Mode 

 

Override 

 

 

 

Comm Lost 

 

 

Cool 

 

 

 

 

 

 

 

 

Sys Mode 

 

 

 

 

 

 

 

 

Heat 

 

 

 

 

 

 

 

 

Current Zone

 

Sequence

 

 

Return Air

 

Temperature

 

 

Discharge Air

 

Temperature

 

 

Current Static

 

Pressure

 

 

 

 

 

 

 

 

Zone Seq 

 

RA Temp 

 

DA Temp 

 

Pressure 

Off 

 

xx.x °C or °F 

 

xx.x °C or °F 

 

x.x WC or Pa 

Zone Seq 

 

 

 

 

 

 

Cool 

 

 

 

 

 

 

Zone Seq 

 

 

 

 

 

 

Heat 

 

 

 

 

 

 

 

Effective PI 

Heat

 

Demand at RTU

 

 

Effective PI Cool 

Demand at RTU

 

 

Highest PI Heat 

Demand Zone

 

Address

 

 

Highest PI Cool 

Demand Zone

 

Address

 

 

 

 

 

 

 

 

Heat Out 

 

Cool Out 

 

Heat MAC 

 

Cool MAC 

xxx % 

 

xxx % 

 

xxx 

 

xxx 

Содержание VZ7656F1000B





























Отзывы: