background image

 

 

  

 

 

 

 

SPECIAL

 

SAFETY

 

INSTRUCTIONS

 

for

 

Lithium

Ion

 

Battery

 

Packs

 

 

o

 

Always charge the battery when the temperature is between 18-24°C (32°F to 113°F). Do not charge the 
battery pack when the temperature is below 0°C (32°F), or above 40°C (113°F) This is important. Failure to 
observe this safety rule could cause serious damage to the battery pack. 
 

o

 

The battery is to be disposed of safely. Do not dispose of the battery pack by incinerating the battery pack . 
The battery pack can explode in a fire. 
 

o

 

Never attempt to open the battery pack for any reason. If the plastic housing of the battery pack breaks 
open or cracks, immediately discontinue its use and do not recharge it. 

 

o

 

Do not store or carry a spare battery pack in a pocket or toolbox or any other place where it may come into 
contact with metal objects. The battery pack may be short circuited causing damage to the battery pack, 
burns or a fire. If storing or disposing the battery pack, cover the terminals with a heavy insulation tape to 
ensure short circuit cannot occur.   

 

o

 

Batteries, when stored for a long period of time, will discharge. If the battery pack has been stored for a long 
time, you should charge the battery pack first before using it. 
 

o

 

Allow the battery pack to cool down after charging. Do not place it in a hot environment such as near a fire, 
in a metal shed or open trailer left in the sun, etc. The best storage place is one that is cool and dry away 
from direct sunlight and excess heat or cold. 

 

o

 

Only charge the battery with the charger supplied. 

 

o

 

Do not splash or immerse in water or other liquids. This may cause premature cell failure. 
 

o

 

A small leakage of liquid from the battery pack may occur under extreme usage or temperature. This does 
not necessarily indicate a failure of the battery pack. However, extra care should be taken during cleanup, 
including wearing chemical-resistant rubber gloves, eye protection and other protective garb. The fluid can 
damage clothing or skin upon contact. After donning appropriate safety wear, wipe battery with a 
disposable dry rag to fully remove fluid and then dispose of rag appropriately. 

 

If

 

the

 

outer

 

seal

 

is

 

broken

 

and

 

this

 

leakage

 

comes

 

into

 

contact

 

with

 

your

 

skin:

 

Wash the affected area quickly with soap and water. 
Neutralise the liquid with a mild acid such as lemon juice or vinegar. 
 

If

 

the

 

leakage

 

gets

 

in

 

your

 

eyes:

 

Flush your eyes with clean water for a minimum of 10 minutes and seek immediate medical 
attention. Inform the medical staff that the liquid is a 25-35% solution of potassium hydroxide. 

 

IF

 

IRRITATION

 

PERSISTS

 

OR

 

FLUID

 

IS

 

INGESTED,

 

SEEK

 

IMMEDIATE

 

MEDICAL

 

ATTENTION!

 

 
 

Содержание V20L2CD3K1











Отзывы: