Vetek WB5040-SWP Скачать руководство пользователя страница 10

9

Weigh Beam BATTERY

- 1.5 volt x 4 “C” alkaline

- User replaceable

- 130+ continuous hours of operation under typical operating conditions

Troubleshooting

Issue Recommendations

“Low Battery” icon blinks on the digital readout, then the indicator powers off.

Recharge the battery. Plug the indicator into 230 VAC for 18+ hours (using the included AC 

adapter). When not operating under battery power, it is recommended that the indicator remains

plugged in to 230VAC. This will keep a full charge in the battery.

Indicator displays a weight after the animal has left the scale.

Check for mechanical binding in the overall equipment set up, such as restraining chains on 

squeeze chute, platform rubbing against walls, or similar. Check weighing platform area for buil-

dup of mud or manure.

Weight reads out lower at one end of the weighing platform/squeeze chute than the other

end.

Check for any type of mechanical binding or impingement of the weigh beam that is displaying 

the lower weight. Check underneath the weigh beam for any obstructions. Make sure that the 

weigh beam feet are not screwed in so far as to restrict downward movement of the weigh 

beam.

Indicator displays six small zeros. 

Scale is overloaded. Remove weight from scale.

Scale turns off on its own. 

The indicator has a power conservation feature, set to automatically power off the scale after 30

minutes of non-use. If your needs require a different setting, call us.

.

Display is erratic. 

The battery may be fully depleted. If so, this condition can cause erratic displays even if the digi-

tal indicator is plugged into 230 VAC. Power off the indicator and fully charge the battery for 18+ 

hours.

Limited 12 month Warranty

This product is warranted by Transcell Technology against manufacturing defects in material

and workmanship under normal use for twelve (12) months from the date of purchase. For com-

plete warranty details and service information, please contact us at the address below.

Contents subject to change without notice.

Vetek Weighing AB

Box 79

76040 Väddö, Sweden

Tel +46176-208920

Fax+46176-208929

Web: www.vetek.com 

Содержание WB5040-SWP











Отзывы: