background image

Subject to modifications.

© Vestamatic GmbH

Art.-Nr.: 

1253 001 GB 2218 A05  •  Vestamatic GmbH  •  Dohrweg 27  •  D-41066 Mönchengladbach 

 •  www.vestamatic.com

7/8

G

P R O  · LL-ME-BAT/I-24/0,6 Nm RB IO-AIR

Programming of additional remote controls

Briefly press the PROG. button at the motorhead. Programming mode 

is now active for 60 sec. while the green LED flashes continuously.

 

Radio remote control IO-AIR Transmitter

 – as described above.

 

Radio wall transmitter IO-AIR Switch

 – as described above.

Successful programming:

The motor briefly performs two ON/UP and OFF/DOWN commands. 

Programming of additional radio transmitter by means of a 

programmed radio transmitter.

 

Select the corresponding channel with the programmed radio trans-

mitter.

 

Press the PROG. and then the STOP button (radio remote control) 

resp. ON /UP button (wall-mounted radio transmitter).

 

The motor is now for 

10 sec. in programming mode.

 The motor per-

forms a short ON/OFF and UP/DOWN movement command.

 

Programming the radio remote control IO-AIR transmitter:

Press the PROG. and then the STOP button.

 

Programming the radio wall transmitter IO-AIR Switch:

Press the PROG. and then the ON /UP button.

Successful programming:

The motor briefly performs two ON/UP and OFF/DOWN commands. 

Option 1

Option 2

 

By means of the programmed radio remote control

 

– Press the PROG. button (see 

figure left) on the back side of 

the radio remote control several 

times until the following LEDs 

flash (Fig. B). Then press the 

STOP button.

 

– The motor briefly performs 

ON/UP and OFF/DOWN com-

mands. Delete mode will now 

be enabled for 10 seconds.

PROG. button

at the back side

Deleting a programmed radio remote control

 

By means of the programmed radio wall transmitter

 

– Press the PROG. button on the 

back side of the radio wall trans-

mitter once, the red LED flashes.

 

– Briefly press the OFF/DOWN 

button. The deletion process is 

terminated after approx. 10 sec.

 

– The motor briefly performs 

ON/UP and OFF/DOWN com-

mands.

PROG. button

LED

Deleting a radio remote control IO-AIR Transmitter

 

Within 10 seconds, press the 

STOP

 button on the radio remote control to be

deleted. When you release the button, the motor briefly performs two 

ON/UP and OFF/DOWN move commands.

 

Cancellation is now effective.

Setting the motor speed

NOTE:

If an already set motor speed is selected, the motor does not 

 execute ON / OFF and OFF / DOWN commands for confirmation.

i

 

Press the PROG. button (see 

figure left) on the back side of 

the radio remote control several 

times until the following LEDs 

flash.

 

For the desired motor speed, 

press one of the following but-

tons:
50 rpm = UP button

  

Q

30 rpm = STOP button

  

·

15 rpm = DOWN button 

 

q

 

The motor briefly performs one 

ON / UP  and  OFF / DOWN  mo-

vement. 

 

The setting of the motor speed 

is completed.

PROG. button

at the back side

Содержание LL-ME-BAT/I-24/0,6 Nm RB IO-AIR









Отзывы: