background image

Subject to modifications.

© Vestamatic GmbH

Art.-Nr.: 

1253 001 GB 2218 A05  •  Vestamatic GmbH  •  Dohrweg 27  •  D-41066 Mönchengladbach 

 •  www.vestamatic.com

5/8

G

P R O  · LL-ME-BAT/I-24/0,6 Nm RB IO-AIR

 

Briefly press the PROG. button at the motor-

head. Programming mode is now active for 

60 sec. while the green LED flashes continuously.

 

Press PROG. button at the back side of the 

 remote  control.

 

LED starts flashing.

 

Press ON/UP button of the channel for pro-

gramming shortly.

 

The motor will give a feedback (two short 

UP / DOWN movements) to confirm that the ins-

tallation procedure has ended.

The flashing of the LED on the back side stops 

after 1 second.

 

To drive the motor in UP or DOWN direction, 

please press the respective button. Motor moves

with a delay, since no final positions are set.

Programming for initial operation respectively after RESET

 

Briefly press the PROG. button at the motor-

head. Programming mode is now active for 

60 sec. while the green LED flashes continu-

ously.

 

Press PROG. button at the back side of the 

 remote  control.

 

LEDs on the front side of the remote control 

start flashing.

 

Press and release the STOP button short-

ly. The motor will give a feedback (two short 

UP / DOWN movements). Programming was 

successful. The flashing of the LEDs on the 

front side of the remote control stops after 

about 1 sec., then the motor can be driven.

 

To drive the motor in UP or DOWN direction, 

please press the respective button. Motor moves

with a delay, since no final positions are set.

PROG. button

at the back side

Radio remote control IO-AIR Transmitter

Radio wall transmitter IO-AIR Switch

PROG. button

LED

 

– Hold down the button 

 or 

 to check the  motor turning direction.

 

– When the motor reacts in opposite direction (when motor goes down

when you press UP and vice-versa), you need to change the motor 

direction. Motor direc tion can only be changed  during installation phase, 

when no limit positions are set.

 

– Shortly press the following combination of buttons (within 10 seconds):

  

  

  

 

– The motor will give a short feedback if the process is finished.

Changing motor turning direction

Setting electronic limit position

ATTENTION!
The motor starts to move with a short delay time during instal-

lation phase, when no limit positions are set. 

Ä

 

– Hold down the button 

 to move the motor in the requested 

lower

limit position.

For precise moving of the motor briefly press the button 

, press 

again and hold.

 

– Press the following button sequence (within 10 seconds): 5 × short 

.

 

– The motor will give a short feedback if the process is finished.

Setting the lower limit position

 

– Hold down the button 

 to move the motor in the requested 

upper

limit position.

For precise moving of the motor briefly press the button 

, press again 

and hold.

 

– Press the following button sequence (within 10 seconds): 5 × short 

.

 

– The motor will give a short feedback if the process is finished.

Setting the upper limit position

The installation procedure is finished and the limit position settings are 

saved.

 

– Press the button 

 or 

= self-locking.

 

– Press the opposite button or STOP button of the radio remote control 

to stop the drive.

Precise controlling with set limit positions

 

– Hold down the button 

 or 

.

The motor now moves at a slower speed and can thus be precisely 

steered to the desired position.

 

– After releasing the directional button, the motor is immediately stopped.

NOTE:

The function is only available when the limit positions have been 

set completely.

i

Содержание LL-ME-BAT/I-24/0,6 Nm RB IO-AIR









Отзывы: