GT-PLXD
AIR SCREWDRIVER
INSTRUCTION MANUAL
Model
GT - PLXD
Capacity
4.0 - 5.0mm
Free Speed
11,000rpm
Overall
Length
198mm
Weight
670g
Air Consumption
0.33m
3
/min
Inner Hose Diam. 6.35mm
Air Pressure
0.6MPa
Accessories
Both End Bit (A14 +2x65G)
1PC
VESSEL Air Plug (BPB-2F)
1PC
ISO VG-10 lubrication oil (Clear)
15cc
ISO VG-32 lubrication oil (Light Green) 15cc
■
LUBRICATION
1. Lubrication is indispensable to air tools.
It is necessary to install a lubricator for automatic oil
feed, but if it is not available, manual lubrication twice a
day is recommended for longer product life and efficient
function of its mechanism. The package contains two
different kinds of lubrication oils.
2. To lubricate the motor part, remove the air hose from Air
Inlet Bushing. Then apply appropriate amount of
lubrication oil for rotating mechanism (VG-10, Clear) into
Air Inlet and conduct several seconds’ idling.
3.
To lubricate the impact-driving parts, remove Lubricant
Port Screw and apply one to two drops of lubrication oil
to impact mechanism (VG-32, Light Green) once a week.
To replace spent lubricant, remove Lubricant Port Screw
and dispose of the old lubricant. Then refill the hammer
housing with 8cc volume of new lubrication oil for
impact driving mechanism (VG-32, Light Green).
Excessive lubrication lowers the working torque.
■
AIR SUPPLY
1. Air tools can be adversely affected by moisture.
As air supplied from the compressor contains a lot of
moisture and dust, it is advisable to install a filtering
equipment and a lubricator in the pipeline to remove
such undesirable elements. Also, accumulated water
within the air tank needs to be drained every day.
2. Before using a new air hose or air pipe, connect it to the
air compressor first to run a flow into it so that the inside
of it will be cleaned.
3. Keep the inside of air hoses and air pipes clean.
With dust and water accumulated within an air hose or
pipe, the inner diameter of them becomes smaller and it
causes a drop in the working air pressure.
It can also cause the air tools to break down if such
objects get into them.
4. If the air hose is detached from the tool, keep the end
of the hose from falling onto the floor as dust or other
objects may come into the air hose.
5. The input air pressure needs to be maintained within
the 0.55MPa to 0.60MPa range by installing a regulator
at the tool end. Excessive air pressure shortens the lifetime
of impact-driving parts and insufficient air pressure lowers
the working torque and causes its performance to be
impaired.
6. Please conduct “idling” for a few seconds after lubrication,
as the lubricant would be flushed out with exhaust air.
7. VESSEL Quick-Change Couplings are recommended for
more convenience.
■
OPERATION
1. Do not tamper with the rotational parts as they are
adjusted with high precision. In case of malfunction,
please contact us for customer service.
2. Switch Reverse Lever to L (for counter-clockwise
revolution) or R (for clockwise revolution) to change
the rotational direction.
3. Select an appropriate level of torque from “1 (MAX)”
to “3 (MIN)” by Adjusting Dial.
4. Set the tool to the screw and press Throttle Lever to start.
5. Release Throttle Lever to stop the revolution after
completing the fastening job. Unnecessary driving will
damage both the screw / bolt and the impact-driving
mechanism.
6.
Do not use the Throttle Lever to hang the unit.
The use of proper hanging equipment is required.
7.
Avoid idling the unit with no load, except for the after-
lubrication flush (Refer to the 6th note of AIR SUPPLY).
■
SPECIFICATIONS
Cover with Air Outlet
Anvil (Rotatable) Throttle Lever Air Inlet Bushing
Adjusting Dial
Bit Sleeve Hammer Housing Reverse Lever
Lubricant port
screw
