VESDA VLC Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 58

background image

VESDA Maintenance Guide

VESDA

20

www.xtralis.com

8.1.3

Replacing the VESDA VLP and VESDA VLS Chassis

Select correct replacement unit

There are four Chassis/Manifold replacement units available for VESDA VLP and VESDA VLS Detectors.
Refer to Table 8-1 below to select the correct part for your detector.

Table 8-1: Part Number Selection

Conditions

Part Number

DetectorModel

VSP-006-NEN

A

B

C

Legend:

l

A: VSP-006-NEN or VSP-009-NEN Label (when fitted)

l

B: Chassis / Manifold Assembly

l

C: Turbulators

VSP-006(VLP

Chassis/Manifold

Assembly(EN54-20))

VSP-009(VLSChassis/Manifold

Assembly(EN54-20))

VSP-006-NEN(VLP

Chassis/Manifold

Assembly(Non-EN54-20))

VSP-009-NEN(VLSChassis/Manifold

Assembly(Non-EN54-20))

VLP

If manifold is fitted with turbulators AND there is NO VSP-006-NEN label
AND firmware version is greater than or equal to 3.17.00.

X

If manifold is NOT fitted with turbulators OR Chassis is labelled with
VSP-006-NEN label OR firmware is less than or equal to 3.15.00.

See

Notes

X

VLS

If manifold is fitted with turbulators AND there is NO VSP-009-NEN label
AND firmware version is greater than or equal to 3.17.00.

X

If manifold is NOT fitted with turbulators OR Chassis is labelled with
VSP-006-NEN label OR firmware is less than or equal to 3.15.00.

See

Notes

X

Notes:

l

In most countries, it is possible to use an EN 54-20 compliant chassis when replacing pre-EN54-20 chassis
(without turbulators). However, under this condition, it may be necessary to increase the size of the sampling
holes to increase the airflow rate (i.e. minimum 20 liters/min) for the new chassis to normalize. Normalization is
the commissioning process whereby the detector establishes the “normal” flow rate. Once normalized, the
detector monitors for deviations in flow rate from the established norm.

l

For France, pre-EN54-20 chassis (without turbulators) and non-EN54-20 chassis are configured to work with
the Fire-Fault (FF) LEDs. Under this condition, it is essential to use a non-EN54-20 chassis to ensure correct
operation of the FF LEDs.

«
...
24
25
26
27
28
...
»

Содержание VLC



























































Отзывы:

Нет отзывов

Похожие инструкции для VLC

Бренд: Radio Shack Страницы: 12

Бренд: ZEBON Страницы: 2

Бренд: Uniel Страницы: 20

Бренд: Zetronix Страницы: 13

Бренд: Ei Electronics Страницы: 14

60.2009 Cone Wake-up Light

Бренд: TFA Страницы: 20

Бренд: Siemens Страницы: 5

Moondance Glow M402SR

Бренд: Altec Lansing Страницы: 28

Бренд: IKEA Страницы: 12

Xtralis ICAM ILS-1

Бренд: Xtralis Страницы: 24

Бренд: BROWIN Страницы: 22

Бренд: BROWIN Страницы: 53

Бренд: BROWIN Страницы: 62

Бренд: Quell Страницы: 31

Бренд: x-sense Страницы: 39

Бренд: x-sense Страницы: 41

Cig-Arrête CSA-FDV

Бренд: Radal Technology Страницы: 2

Бренд: Valet Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды