background image

LIEBERT® PSP

TM

Quick Installation Guide

590-1631-501A\SLI-23285_REV1_11-17

  

 1

IMPORTANT SAFETY 

INSTRUCTIONS

•  Do not connect equipment that 

may overload the UPS or 

demand half-wave rectification, 

such as a laser printer.

•  Connect the UPS only to an 

earthed / grounded socket that 

meets electrical safety 

guidelines.

•  Locate the UPS near a wall 

socket. Do not use an extension 

cord between the UPS and the 

socket.

•  Use CE-marked cables only for 

connections between mains, 

the UPS and equipment.

•  The Liebert PSP has been 

designed for small office/home 

office use only; it is NOT 

recommended for use in life-

support applications.

•  In the event of an emergency, 

press the On/Off button and 

disconnect the power cord 

from the AC mains to properly 

disable the UPS.

•  Do not attach power strips or 

surge suppressors to the UPS.

•  Do not attempt to service any 

parts inside the UPS except 

when replacing the batteries. 

Failure to adhere to this could 

cause personal injury or 

equipment malfunction and 

void the warranty.

•  This unit uses components that 

are dangerous for the 

environment, such as electronic 

cards and other electronic 

components. Any component 

that is removed must be taken 

to specialized collection and 

disposal centers. If this unit 

must be dismantled, this must 

be done by specialized 

personnel who are properly 

trained and qualified. The unit 

must be taken to a center 

specialized in collection and 

disposal of dangerous 

substances.

For technical support: visit        

www.vertivco.com

SETUP
1.  Inspecting the package

Inspect the package and the 

UPS upon receipt.
Notify the carrier and dealer of 

visible damage.
The package includes:

•  Liebert PSP
•  USB cable
•  Quick-start guide
•  2 IEC output cables

The Liebert MultiLink™ 

software may be downloaded 

from the Liebert Web site at: 

multilink.liebert.com

See Step 7 for installation 

instructions.

2.  Decide Where to Place the 

UPS

The UPS must be placed 

indoors, protected from water, 

direct sunlight and excessive 

heat.
Provide at least 100mm (4”) of 

clearance on all sides of the 

unit for proper ventilation.

3.  Charging the UPS Battery 

before use

The UPS battery is not charged 

before shipping. It MUST be 

charged before use.

•  Use the input power cord 

from computer equipment as 

the input power cord of UPS 

Connect a user-supplied 

power cord from the UPS to a 

wall socket and charge for at 

least eight hours. Unit can be 

charged in the on or off  state.

Liebert® PSP

TM

 UPS

Содержание PSP500MT3-230U

Страница 1: ...ther electronic components Any component that is removed must be taken to specialized collection and disposal centers If this unit must be dismantled this must be done by specialized personnel who are properly trained and qualified The unit must be taken to a center specialized in collection and disposal of dangerous substances For technical support visit www vertivco com SETUP 1 Inspecting the pa...

Страница 2: ...Liebert MultiLink software Install the software See the Liebert MultiLink quick start guide or user manual for installation instructions Connect one end of the USB cable supplied to the USB port on the rear of the UPS Connect the other end to a USB port on the computer See the Liebert MultiLink user manual for operating instructions NOTE Vertiv recommends connecting the USB cable directly to the c...

Страница 3: ...o the negative terminal NOTE Small sparks may occur at the battery connectors during reconnection Take care not to short circuit the positive and negative battery terminals while replacing the battery Place the battery in the UPS 4 Reassembling the PSP outer case Ensure correct alignment of front panel then reattach the right side cover Evenly tighten the four screws from Step 1 DO NOT overtighten...

Страница 4: ...ve Form Stepped sine wave VRLA Battery Type VDC x Ah x Quantity 12V x 7 2Ah x 1 12V x 7 2Ah x 1 Typical Recharge Time 6 8 hours to 90 Battery Run Time See Load Autonomy table below Audible and Visual Audible alarm LED Backup Sockets IEC 320 C13 3 Surge Sockets IEC 320 C13 1 Operating Temperature C F 0 to 40 32 to 104 Storage Temperature C F 15 to 40 5 to 104 Storage Temperature C F 15 to 40 5 to 1...

Отзывы: