Vertiv Liebert DA250 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 91

background image

Charging DA265 Air Cooled Systems (Liebert® DA265 without Receivers)

NOTICE

Risk of improper refrigerant charging. Can cause equipment damage.

R-410A is a blended refrigerant and must be introduced and charged from the cylinder only as a liquid.

When adding liquid refrigerant to an operating system, it may be necessary to add the refrigerant through the
compressor suction service valve. Care must be exercised to avoid damage to the compressor. We recommend
connecting a sight glass between the charging hose and the compressor suction service valve. This will permit
adjustment of the cylinder hand valve so that liquid can leave the cylinder while allowing vapor to enter the
compressor.

NOTICE

Risk of improper operation. Can cause compressor failure.

Operating the unit with the EEV closed can cause compressor failure. The reheat and humidifier are disabled. A
minimum of 20 psig (138 kPa) must be established and maintained for the compressor to operate. The
charging function can be reset as many times as required to complete.

To charge the system:

1.

Check the nameplate on the indoor unit for the refrigerant type to be used. Unit control configurations differ
depending upon the refrigerant type.

2.

The unit must be operating during charging. Refer to

Checklist for Completed Installation

3.

Calculate the amount of charge for the system. See

Refrigerant Charge Requirements for Air Cooled Systems

4. Accurately weigh in as much of the system charge as possible before starting the unit. Do not exceed the

calculated charge by more than 0.5 lb (0.37 kg).

5.

Close the Liebert® MCV heat rejection skid disconnect switch.

•

Unit must be charged with the return air /- 10°F (5.5° C) of the operating point.

•

If the operating point changes, the charge may need to be adjusted according to the new operating
point.

•

The return air temperature to the unit being charged must be stable. If this is not possible due to the lack
of heat load, then the load banks must be used to offset the cooling load during startup.

6. Close the Liebert® DSE disconnect switch.

7.

In the Service menu of the Liebert® iCOM™ controller, select

Diagnostics/Service > Diagnostics

.

a. Enable Manual Mode.

NOTE: Manual mode will time out after 30 minutes.

b. In the Search Box type

E177

and press Enter.

Two parameters appear in the Parameter Directory (E177.1 and E177.2).

Press the Gear icon in the upper right corner.

Select

Make Writeable

.

Change E177.1 and E177.2 from 15 minutes to 2 minutes.

This will reduce the superheat setpoint from 24°F (13.3° C) to 13°F (7.2° C) degrees in two minutes.

6 Piping and Refrigerant Requirements

35

«
...
37
38
39
40
41
...
»

Содержание Liebert DA250




























































































Отзывы:

Нет отзывов

Похожие инструкции для Liebert DA250

Бренд: Keithley Страницы: 36

Бренд: Rain-Flo Irrigation Страницы: 16

Бренд: JB-Lighting Страницы: 60

Бренд: Olsen Страницы: 56

Бренд: Waterous Страницы: 5

Бренд: 3TECH Страницы: 32

Бренд: 4EVAC Страницы: 15

Бренд: B&G Страницы: 3

Бренд: Raven Страницы: 12

Бренд: Zero 88 Страницы: 20

Бренд: Kapriol Страницы: 32

Бренд: Cabletron Systems Страницы: 33

Бренд: i-CAT Страницы: 32

Бренд: Mainca Страницы: 21

Бренд: Daktronics Страницы: 30

Бренд: DAKOTA ULTRASONICS Страницы: 28

Бренд: Eaton Страницы: 16

RMQ-Titan C22-PV Series

Бренд: Eaton Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды