Vertiv eSure C48/58-1000B Скачать руководство пользователя страница 10

Страница: 10 / 40

Vertiv

eSure™ Power Extend Converter Mounting Bracket Kit Installation Manual (IM565460)

Rev. A

[ ] 4.

Completely remove the four (4) screws (two per side) that secured the shield to the

TOP

distribution panel. Save two (2) screws for later re-assembly. See

Figure 2

Figure 2:

Remove Screws from Top Distribution Panel

[ ] 5.

Remove the bottom two (2) screws and flat washers (one per side) that secures the

TOP

distribution panel to the cabinet. These will not be reused. See

Figure 3

Figure 3:

Remove Screws from Top Distribution Panel

[ ] 6.

Orient the kit supplied left side mounting bracket as shown in

Figure 4

(top distribution panel).

Note that the bracket comes preassembled with mounting hardware. Slide the mounting bracket
into position and secure with the captive hardware. Re-assemble the screw saved in [ ] 4. above.
Torque all hardware as indicated in

Figure 4

Remove

these

screws.

Remove

these

screws.

582137000 List AC

Distribution Panel

(others similar)

Remove this

screw and flat

washer.

Remove this

screw and flat

washer.

582137000 List AC

Distribution Panel

(others similar)

Содержание eSure C48/58-1000B









































Результаты поиска

Содержание eSure C48/58-1000B

Отзывы:

Бренды по названию

Популярные бренды

Vertiv eSure C48/58-1000B, Руководство по установке

Результаты поиска

Содержание eSure C48/58-1000B

Отзывы:

Бренды по названию

Популярные бренды