background image

FCC ID: K6610354640

IC ID: 511B-10354640

Alignment

1

/

10

Vertex Standard Co., Ltd.

VX-4107/4207 Alignment

Introduction

The VX-4100/4200 series are carefully aligned at the factory for the specified

performance across the frequency range specified for each version. Realignment should
therefore not be necessary except in the event of a component failure, or altering version type.
All component replacement and service should be performed only by an authorized 

Vertex

Standard

 representative, or the warranty policy may be void.

The following procedures cover the sometimes critical and tedious adjustments that are

not normally required once the transceiver has left the factory. However, if damage occurs and
some parts subsequently are placed, realignment may be required. If a sudden problem occurs
during normal operation, it is likely due to component failure; realignment should not be done
until after the faulty component has been replaced.

We recommend that servicing be performed only by authorized 

Vertex Standard

 service

technicians who are experienced with the circuitry and fully equipped for repair and alignment.
Therefore, if a fault is suspected, contact the dealer from whom the transceiver was purchased
for instructions regarding repair. Authorized 

Vertex Standard

 service technicians realign all

circuits and make complete performance checks to ensure compliance with factory
specifications after replacing any faulty components.

Those who do undertake any of the following alignments are cautioned to proceed at

their own risk. Problems caused by unauthorized attempts at realignment are not covered by
the warranty policy. Also, 

Vertex Standard

 reserves the right to change circuits and alignment

procedures in the interest of improved performance, without notifying owners.

Under no circumstances should any alignment be attempted unless the normal function

and operation of the transceiver are clearly understood, the cause of the malfunction has been
clearly pinpointed and any faulty components replaced, and realignment determined to be
absolutely necessary.

The following test equipment (and thorough familiarity with its correct use) is necessary

for complete realignment. Correction of problems caused by misalignment resulting from use of
improper test equipment is not covered under the warranty policy. While most steps do not
require all of the equipment listed, the interactions of some adjustments may require that more
complex adjustments be performed afterwards.

Do not attempt to perform only a single step unless it is clearly isolated electrically from

all other steps. Have all test equipment ready before beginning, and follow all of the steps in a
section in the order presented.

Содержание VX-4107











Отзывы: