background image

FCC ID: K6630173X3D 

IC ID: 511B-30173X3D 

Alignment 

2/5

 

Vertex Standard Co,. Ltd. 

Required Test Equipment  

 

RF Signal Generator with calibrated output level at 200 MHz   

 

Deviation Meter (linear detector)  

 

AF Millivoltmeter  

 

SINAD Meter 

 

Inline Wattmeter with 5% accuracy at 200 MHz 

 

Regulated DC Power Supply: 13.8 VDC, 10A 

 

50-ohm Non-reactive Dummy Load: 30W at 200 MHz 

 

Frequency Counter: >0.1 ppm accuracy at 200 MHz 

 

AF Signal Generator  

 

DC Voltmeter: high impedance 

 

VHF Sampling Coupler 

 

AF Dummy Load: 4 Ohms, 10 W  

 

Oscilloscope 

 

Spectrum Analyzer 

 

GX3500S Marine Transceiver 

 
 
Alignment Preparation & Precautions

 

A dummy load and inline wattmeter must be connected to the main antenna jack in all 

procedures that call for transmission. Correct alignment is not possible with an antenna.  

After completing one step, read the following step to determine whether the same test 

equipment will be required. If not, remove the test equipment (except dummy load and 
wattmeter, if connected) before proceeding. 

Correct alignment requires that the ambient temperature be the same as that of the 

transceiver and test equipment, and that this temperature be held constant between 20°C 
and 30°C (68°F and 86°F). When the transceiver is brought into the shop from hot or cold 
air it should be allowed some time for thermal equalization with the environment before 
alignment. If possible, alignments should be made with oscillator shields and circuit boards 
firmly affixed in place. Also, the test equipment must be thoroughly warmed up before 
beginning. 
 

Note: Signal levels in dB referred to in this procedure are based on 0 dBµ = 0.5 µV (closed 
circuit). 

 
Overview of Test Mode 

The test mode has been build in the microprocessor in order to adjust and confirm the 

performance of transceiver. 

The purpose is to adjust transceiver simply and to confirm the performance of 

transceiver smoothly. 
 

Содержание GX1500S






Отзывы: