Vertex Standard GX1000S Скачать руководство пользователя

Страница: 4 / 6

FCC ID: K6630303X3S

IC ID: 511B-30303X3S

Alignment

4/6

Vertex Standard Co,. Ltd.

Adjustment of Receiver Front-end

Adjust the receiver front-end coil.

Setup the test equipment as shown below.

Set the center frequency of the spectrum analyzer to 159.00 MHz, set SPAN to 20.00

MHz, set RBW and VBW to 30 KHz, and set SWP to 56 ms.

Adjust

1010

L1012

L1022

L1026

, and

L1027

until the wave form shown in below is

obtained.

Note

: Adjust the output of the tracking generator so that RF AMP and spectrum analyzer

will not saturate.

Figure shows the reference wave form. The wave form varies with measuring instruments.

It is impotent to take the lowest possible value at the stop band near 150 MHz and the

highest possible value at the band near 156 MHz.

Each coil shall be adjusted at the range between the initial condition and right and left

revolving.

GX1255S-FRONT-END

ATTEN 20dB

RL 10.0dBm

10dB/

CENTER 159.00 MHz

*RBW 30 kHz

VBW 30 kHz

SPAN 20.00 MHz

SWP 56.0 ms

Содержание GX1000S







Результаты поиска

Содержание GX1000S

Отзывы:

Похожие инструкции для GX1000S

Бренды по названию

Популярные бренды

Vertex Standard GX1000S, Руководство по настройке

Результаты поиска

Содержание GX1000S

Отзывы:

Похожие инструкции для GX1000S

Бренды по названию

Популярные бренды