VersaLogic Viper VL-EBX-38EBP Скачать руководство пользователя страница 17

Страница: 17 / 79

EBX-38 Hardware Reference Manual

Configuration and Setup

Initial Configuration

The following components are recommended for a typical development system.



VL-EBX-38 single board computer



VL-MM9-xxEBN DDR3L SO-DIMM module (see System RAM)



ATX power supply with motherboard and disk drive connectors



VGA video monitor



USB Keyboard



USB Mouse



SATA hard drive

The following VersaLogic cables and accessories are recommended.



EBX-38 cable kit (CKR-VIPER)



VGA Video adapter cable (CBR-1204)



User I/O cable (CBR-4005) and accompanying paddleboard (CBR-4005B)



VL-CBR-0702 – SATA data cable



VL-CBR-2022 – ATX to 5V power adapter (or VL-CBR-1203 ATX to 12V power adapter)



(Cat5e cables)

Note:

Only one of the listed power adapters can be used.

You will also need a Windows* (or other OS) installation CD/DVD and corresponding drive.

Basic Setup

The following steps outline the procedure for setting up a typical development system. The EBX-

38 should be handled at an ESD workstation or while wearing a grounded antistatic wrist strap.
Before you begin, unpack the EBX-38 and accessories. Verify that you received all the items you

ordered. Inspect the system visually for any damage that may have occurred in shipping. Contact

[email protected]

immediately if any items are damaged or missing.

Gather all the peripheral devices you plan to attach to the Viper as well as their interface and

power cables.
It is recommended that you attach standoffs to the board (see Hardware Assembly

)

to stabilize

the board and make it easier to work with.

Содержание Viper VL-EBX-38EBP
















































































Результаты поиска

Содержание Viper VL-EBX-38EBP

Отзывы:

Бренды по названию

Популярные бренды

VersaLogic Viper VL-EBX-38EBP, Справочник по аппаратуре

Результаты поиска

Содержание Viper VL-EBX-38EBP

Отзывы:

Бренды по названию

Популярные бренды