VersaLogic EPM-15 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 52

background image

Configuration and Setup

EPM-15 Reference Manual

12

Shadow Configuration

+------------------------------------------------------------------------------+
| System BIOS Setup - Shadow/Cache Configuration |
| (C) 2005 General Software, Inc. All rights reserved |
+---------------------------------------+--------------------------------------+
| Shadowing :>Chipset | Shadow 16KB ROM at C000 : Enabled |
| Shadow 16KB ROM at C400 : Enabled | Shadow 16KB ROM at C800 : Disabled |
| Shadow 16KB ROM at CC00 : Disabled | Shadow 16KB ROM at D000 : Disabled |
| Shadow 16KB ROM at D400 : Disabled | Shadow 16KB ROM at D800 : Disabled |
| Shadow 16KB ROM at DC00 : Enabled | Shadow 16KB ROM at E000 : Enabled |
| Shadow 16KB ROM at E400 : Enabled | Shadow 16KB ROM at E800 : Enabled |
| Shadow 16KB ROM at EC00 : Enabled | Shadow 64KB ROM at F000 : Enabled |
+---------------------------------------+--------------------------------------+

Note:

Due to changes and improvements in the system BIOS, the information on your
monitor may differ from that shown above

.

Operating System Installation

The standard PC architecture used on the EPM-15 makes the installation and use of most of the
standard x86 processor-based operating systems very simple. The operating systems listed on the

VersaLogic OS Compatibility Chart

use the standard installation procedures provided by the

maker of the OS. Special optimized hardware drivers for a particular operating system, or a link
to the drivers, are available at the EPM-15 Product Support web page at

http://www.versalogic.com/private/manxsupport.asp

.

«
...
16
17
18
19
20
...
»

Содержание EPM-15





















































Отзывы:

Нет отзывов

Похожие инструкции для EPM-15

945GC MICRO 775

Бренд: Biostar Страницы: 49

Бренд: ECS Страницы: 46

Бренд: ASROCK Страницы: 160

Бренд: Gigabyte Страницы: 18

Бренд: Thinklabs Страницы: 129

Бренд: Supermicro Страницы: 105

Бренд: Gigabyte Страницы: 32

Бренд: Ublox Страницы: 2

Бренд: Semtech Страницы: 16

Бренд: Mach Страницы: 86

X99A WORKSTATION

Бренд: MSI Страницы: 97

Бренд: Foxconn Страницы: 111

Бренд: Nuvoton Страницы: 11

Бренд: Avalue Technology Страницы: 60

Бренд: Golden Motor Страницы: 22

Бренд: AAC Microtec Страницы: 106

Бренд: Fujitsu Страницы: 30

Бренд: IEI Technology Страницы: 129

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды