manualshive.com logo in svg

Vermont Castings VM508, Процедуры сборки

Поделиться
Скачать
Vermont Castings VM508 Скачать руководство пользователя страница 13

13

50004428

VM508 / VM658 Assembly

CAUTION: Some parts may have sharp edges; to avoid injury, wearing gloves during assembly, lifting or mov-
ing the grill is recommended.

Step 15:  Interior Shelf Installation

(Model VM658)

Parts Required:

 

(2) #10-24 x 3/8” Screws (50004268

 

(1) Rod

 

(1) Washer Nylon (50000192)

 

(1) 10-24 Pan Quad. Nut (10006126)

 

(1) Interior Shelf

Figure 16

Place two (2) 10-24 x 3/8” screws 
on the threaded holes located on left 
side panel. Install the rod in hole in 
bottom panel. Make sure the connec-
tion between the rod and the bottom 
panel is tight. Place washer nylon on 
top of rod. Slide interior shelf in place. 
Back flange edge of shelf slides into 
clip on back panel. Use 10-24 Pan 
Quad nut to secure interior shelf to 
rod.

����
����������������������
����

Interior Shelf  

#10-24 Pan Quad Nut

Rod

B162

Figure 16

#10-24 x 3/8” Screw
(50004268)

Shelf clip

Step 17: Install LP Tank Pull Out Drawer Assembly

For VM658 Models only.

Follow Pull Out Drawer Assembly instructions to assemble.

Step 16:  Attach Tank Retainer

(Model VM508 Series Only)

Parts Required:

 

(1) Tank Retainer

Figure 17

Attach tank retainer to back panel as shown by pressing 
retainer into back panel bosses.

����
�������������
�����

B241

Figure 17

Bosses

Tank Retainer

Содержание VM508

















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды