manualshive.com logo in svg

VERDER AIR VA 8 810.6012, Инструкция-перечень запасных частей

Поделиться
Скачать
VERDER AIR VA 8 810.6012 Скачать руководство пользователя страница 3

819.6247

3

HAZARDOUS FLUIDS

Improper handling of hazardous fluids or inhaling toxic vapors can cause extremely serious injury or death from
splashing in the eyes, ingestion, or bodily contamination. Observe all the following precautions when you handle
hazardous or potentially hazardous fluids.

Know what fluid you are pumping and its specific hazards. Take precautions to avoid a toxic fluid spill.

Always wear appropriate clothing and equipment, such as eye protection and breathing apparatus, to protect
yourself.

Store hazardous fluid in an appropriate, approved container. Dispose of it according to all Local, State, and
Federal guidelines for hazardous fluids.

Secure the fluid outlet hose tightly into the receiving container to prevent it from coming loose and improperly
draining the fluid.

Pipe and dispose of the exhaust air safely, away from people, animals, and food handling areas. If the dia-
phragm fails, the fluid is exhausted along with the air. See 

Air Exhaust Ventilation

 on page 4.

FIRE AND EXPLOSION HAZARD

Static electricity is created by the flow of fluid through the pump and hose. If the equipment is not properly
grounded, sparking may occur. Sparks can ignite fumes from solvents and the fluid being pumped, dust par-
ticles, and other flammable substances, whether you are pumping indoors or outdoors, and can cause a fire or
explosion and serious injury and property damage.

To reduce the risk of static sparking, ground the pump and all other equipment used or located in the work
area. Check your local electrical code for detailed grounding instructions for your area and type of equip-
ment. See 

Grounding 

on page 4.

If you experience any static sparking or even a slight shock while using this equipment, 

stop pumping

immediately.

 Check the entire system for proper grounding. Do not use the system again until you have

identified and corrected the problem.

Pipe and dispose of the exhaust air safely, away from all sources of ignition. If the diaphragm fails, the fluid is
exhausted along with the air. See 

Air Exhaust Ventilation

 on page 4.

Never

 use a polypropylene or Kynar

 pump with non-conductive flammable fluids as specified by your local

fire protection code. Refer to 

Grounding

 on page 4 for additional information. Consult your fluid supplier to

determine the conductivity or resistivity of your flui

d.

Provide fresh air ventilation to avoid the buildup of flammable fumes from solvents or the fluid being pumped.

Do not smoke in the work area. Do not operate the equipment near a source of ignition or an open flame,
such as a pilot light.

Warning

Comply with all applicable local, state and national fire, electrical and safety regulations.

Содержание AIR VA 8 810.6012

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды