manualshive.com logo in svg

VERDER 810.0077, Инструкция-перечень запасных частей

Поделиться
Скачать
VERDER 810.0077 Скачать руководство пользователя страница 2

819.4470

2

Table of Contents

Safety Warnings

2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Symbols

2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Installation

4

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Operation

10

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Maintenance

11

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Troubleshooting

12

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Service

Repairing the Air Valve

14

. . . . . . . . . . . . . . . . . . . . . . . . . . . 

Ball Check Valve Repair

16

. . . . . . . . . . . . . . . . . . . . . . . . . . 

Diaphragm Repair

17

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Bearing and Air Gasket Removal

20

. . . . . . . . . . . . . . . . . . 

Pump Listing

22

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Repair Kit Listing

23

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Parts

24

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Torque Sequence

28

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Dimensions

29

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Technical Data and Performance Chart

30

. . . . . . . . . . . . . . . . 

Customer Services/Guarantee

32

. . . . . . . . . . . . . . . . . . . . . . . . 

Symbols

Warning Symbol

Warning

This symbol alerts you to the possibility of serious injury or
death if you do not follow the instructions.

Caution Symbol

Caution

This symbol alerts you to the possibility of damage to or de-
struction of equipment if you do not follow the instructions.

EQUIPMENT MISUSE HAZARD

Equipment misuse can cause the equipment to rupture or malfunction and result in serious injury.

D

This equipment is for professional use only.

D

Read all instruction manuals, tags, and labels before operating the equipment.

D

Use the equipment only for its intended purpose. If you are not sure, call  VERDER After Sales Service.

D

Do not alter or modify this equipment.

D

Check equipment daily. Repair or replace worn or damaged parts immediately.

D

Do not exceed the maximum working pressure of the lowest rated component in your system. This equip-
ment has an 8.4 bar maximum working pressure at 8.4 bar maximum incoming air pressure.

D

Use fluids and solvents which are compatible with the equipment wetted parts. Refer to the Technical Data
section of all equipment manuals. Read the fluid and solvent manufacturer’s warnings.

D

Do not use 1,1,1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or fluids con-
taining such solvents in pressurized aluminum equipment. Such use could result in a chemical reaction, with
the possibility of explosion.

D

Do not use hoses to pull equipment.

D

Route hoses away from traffic areas, sharp edges, moving parts, and hot surfaces. Do not expose VERDER
hoses to temperatures above 82

_

C or below -40

_

C.

D

Do not lift pressurized equipment.

D

Comply with all applicable local, state, and national fire, electrical, and safety regulations.

Warning

INSTRUCTIONS

Warning

Содержание 810.0077



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды