manualshive.com logo in svg

VERDER 810.0077, Инструкция-перечень запасных частей

Поделиться
Скачать
VERDER 810.0077 Скачать руководство пользователя страница 13

819.4470

13

Troubleshooting

PROBLEM

CAUSE

SOLUTION

Fluid in exhaust air.

Diaphragm ruptured.

Replace. See pages 17–19.

Loose diaphragm shaft bolt (107).

Tighten or replace. See pages 17–19.

Damaged o-ring (108).

Replace. See pages 17–19.

Pump exhausts excessive  air at stall.

Worn air valve block (7

{H

), o-ring (6

{H

),

plate (8

H

), pilot block (18), u-cups (10),

or pilot pin o-rings (17

{H

).

Repair or replace. See pages 14–15.

Worn shaft seals (402).

Replace. See pages 17–19.

Pump leaks air externally.

Air valve cover (2) or air valve cover
screws (3) are loose.

Tighten screws. See page 15.

Air valve gasket (4

{H

) or air cover gas-

ket (22) is damaged.

Inspect; replace. 
See pages 14–15, 20–21.

Air cover screws (25) are loose.

Tighten screws. See pages 20–21.

Pump leaks fluid externally from ball
check valves.

Loose manifolds (102, 103), damaged
seal between manifold and seat (201),
damaged o-rings (202).

Tighten manifold bolts (106) or replace
seats (201) or o-rings (202). See
page 16.

Содержание 810.0077



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды