Verasys Boiler Controller Quick Start Guide
6
Setting the controller address using the local display
1.
To access the menu, press
ENT.
2.
To navigate to the
Controller
menu
use the up and down
arrows and press
ENT
.
3.
Navigate to the
Network
section and press
ENT
.
4.
Navigate to the
Address
section and press
ENT
.
5.
The address defaults to 4. Press
ENT
again.
The address blinks.
6.
To increase or decrease the address value, use the up or down
arrows.
7.
To confirm the address value, press
ENT.
The address stops blinking and the old address appears.
8.
To refresh the screen, press the up or down arrows. The new
address appears.
9.
Press ESC until you return to the main screen that shows the
system is operational.
Configuring sensors
To configure the installed sensors, complete the following steps:
1. Navigate to the
Details
menu.
2. Navigate to the
Sensors
section.
3. Select the installed sensors using the drop-down menus for each
parameter.
Commissioning the system
To activate the outputs and verify system operation, use the
Commissioning
menu. From the
Commissioning
menu, change
Start Commissioning
to
Trigger
and adjust outputs individually.
Configuration menu options
The following table describes the
System Configuration
menu on
the Smart Building Hub (SBH).
Technical specifications
Table 5:
System Configuration menu options
(Part 1 of 2)
Menu option
Description
Range
Number of Boilers
Sets the number of
boilers
Adjustable
:
1-4
Primary Pump Type
Sets the type of primary
pumps in the system
Adjustable:
• Constant
Speed
• Variable
Speed
Constant Primary
Pump
Sets the pump
configuration
Adjustable
:
• Dedicated
• Parallel
Number of Pumps
Sets the number of
primary pumps
Adjustable
:
1-4
Primary Pump
Operation Type
Sets the pumps
operation type
Adjustable
:
• Duty/Standby
• Lead/Lag
Number of
Secondary Pumps
Sets the number of
secondary pumps (if
any)
Adjustable:
0-4
Secondary Pump
Operation Type
Sets the pump
operation type
Adjustable
:
• Duty/Standby
• Lead/Lag
Bypass Valve
Installed
If there are no
secondary pumps, this
sets the installation of a
bypass valve
Adjustable
:
• No
• Yes
Enable Alarms
This option sets the
enabling/disabling of
alarms
Adjustable
:
• Disable
• Enable
Product code
numbers
LC-VAC3000-0 Verasys 32 point 24 V Application
Controller with Display
Supply
voltage
24 VAC, 20 VAC minimum / 30 VAC maximum, 50/
60 Hz, power supply class 2
North America, safety extra-low voltage (SELV)
Europe
Power
consumption
20 VA maximum for LC-VAC3000-0
VA rating does not include any power supplied to the
peripheral devices connected to binary outputs
(BOs) or configurable outputs (COs). This can
consume up to 12 VA for each BO or CO for a
possible total consumption of an additional 60 VA
maximum.
Ambient
conditions
Operating:
-20°C to 70°C (-4°F to 158°F); 10% to
95% RH noncondensing; pollution degree 2
Storage:
-40°C to 85°C (-40°F to 185°F); 5% to 95%
RH noncondensing
Addressing
BACnet® MS/TP:
valid field controller device
addresses 4–127
Device addresses 0–3 and 128–255 are reserved
and not valid field controller addresses
Communica-
tions bus
BACnet® MS/TP, through RS-485:
3-wire system bus between the supervisory
controller and field controller
4-wire sensor bus between controller, network
sensors and other SA devices, includes a lead to
source 15 VDC supply power from controller to bus
devices
Processor
RX631 Renesas® 32-bit microcontroller
Memory
16 MB flash memory and 8 MB RAM
Table 5:
System Configuration menu options
(Part 2 of 2)
Menu option
Description
Range
