manualshive.com logo in svg

Veolia HDF 12 Series, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Veolia HDF 12 Series Скачать руководство пользователя страница 34

34

Operation & maintenance manual, Drum filter HDF 12/16/20/24 -series

8.6.4 Replacing the drive chain

1. Stop the filter (turn the main power switch to the OFF (0) position and lock it with a padlock).

2. Loosen the four nuts that hold the worm gear in place; see Figure 8.12.

3. Loosen the nut that locks the adjustment screw.

4. Lower the worm gear using the adjustment screw.

5. Split the chain and remove it.

6. Fit the new chain and lock it with a pin.

7. Adjust the drive chain tension according to section 8.6.3 Adjusting drive chain tension.

8. Start operation again as set out in section 6.1.

The chain tension of a new chain must be checked after 10 hours of operation.

8.7 Worm gear motor

For information about maintenance of the worm gear motor, see Appendix F.

8.8 Rubber seal

The rubber seal for the inlet (between the 

filter frame and drum) must be checked to 

ensure that it is free from damage and does 

not leak, see the maintenance chart.

NB.

 Prior to service, read section 2.7 (Safety 

instructions).

Figure 8.13 Inlet rubber seal

Содержание HDF 12 Series









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды