manualshive.com logo in svg

Veolia HDF 12 Series, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Veolia HDF 12 Series Скачать руководство пользователя страница 25

25

Operation & maintenance manual, Drum filter HDF 12/16/20/24 -series

8.3 Bearings

8.3.1 Lubrication

HDF 12, 16, 20 -series filter:

The drum’s centre shaft has slide bearings that must be lubricated.

The support wheels have ball bearings that must be lubricated. 

The bearings should be lubricated per the maintenance chart (see section 8.9). Lubrication stick-

ers (see figure 8.5) that specify the lubrication points are affixed to the filter.

NB.

 Prior to service, read section 2.7 (Safety instructions).

HDF24 series filter:

The drum’s centre’s shaft is equipped with ball bearings that 

must be lubricated.

The support wheels have ball bearings that must be lubricated.

The bearings should be lubricated per the maintenance chart 

(see section 8.9).

Lubrication stickers that specify the lubrication points are affixed to the filter.

NB.

 Prior to service, read section 2.7 (Safety instructions).

8.3.2 Checking centre bearings for wear

The centre shaft bearings must be checked for wear per the maintenance chart.

Figure 8.5 Lubrication sticker

Содержание HDF 12 Series









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды