manualshive.com logo in svg

Veolia ELGA PURELAB Option-S 15-US, Руководство оператора, Страница: 20 / 34

Поделиться
Скачать
Veolia ELGA PURELAB Option-S 15-US Скачать руководство пользователя страница 20

PURELAB Option-S 7/15 US Operator Manual 

ELGA 

Page 16 

PURELAB Option-S 7/15 US  Version 1  08/14 

Step 4 - Water Purity Unit Setting 

This screen enables the preferred water purity unit of measure 
to be set, to either, 

M

Ω

.cm 

or 

µS/cm

. Once selected, all future 

water purity measurements will be displayed with your unit of 
choice. Select the option required using the 

  button and 

accept with the 

 button. 

Step 5 - Purity Alarm Setting 

This screen is used for setting the value at which the water 
purity alarm will activate. 

If the 

M

Ω

.cm

  water purity alarm unit setting was chosen, then 

the following water purity alarm choices will be displayed. 

 

10 M

Ω

.cm

 

 

 

5 M

Ω

.cm 

 

 

1 M

Ω

.cm 

 

If the 

µS/cm

  water purity alarm unit setting was chosen, then 

the following water purity alarm choices will be displayed. 

 

0.1 µS/cm

 

 

 

0.2 µS/cm 

 

 

1.0 µS/cm 

 

Select the alarm setting required using the 

 button and accept 

with the 

 button. 

Note: 

To reset any of the setup parameters, 
restart from the set-up menu and follow 
instructions from Step 1. 

Setting Up Display and Replacement Timers 

Turn the unit off at the power inlet module. To enter the 
replacement timer set up, press the left hand touch pad button 
and at the same time turn the power on.  

A graphic of the ion-exchange cartridge, UV lamp, pre-treatment 
cartridge and clock graphics are displayed with hourly timer 
status. 

CAUTION! 

Before re-setting any of the cartridge 
timers, ensure that the appropriate new 
cartridges have been installed and 
securely located correctly in the PURELAB 
Option-S US. 

Step 1 - Ion-exchange Cartridge Replacement Timer 

Setting this screen will cause the Ion-exchange cartridge timer 
to reset to the preset value of 4380 hours (6 months). 

Press 

 to jump to the next consumable or 

 to initiate reset. 

Press 

 to reset timer or press   to abort reset. 

Press 

 to jump to the next consumable. 

MegaOhm MicroSiemen

 

Purity Alarm Setting 

 

Ion-exchange Cartridge Timer 

MegaOhm

MicroSiemen

 

Water Purity Settings 

Содержание ELGA PURELAB Option-S 15-US



































Отзывы:

Нет отзывов