Vents VUE 300 H2 MINI EC A14 Скачать руководство пользователя | Manualshive

Страница: 6 / 24

background image

6

VUT/VUE 300 V2/H2 mini EC

www.ventilation-system.com

DESIGN AND FUNCTIONING

The unit has the following operating principle: warm stale extract air from the room flows into the unit, where it is filtered by the extract
filters, then air flows through the heat exchanger and is exhausted outside by the extract fan. Cold fresh air from the outside flows into
the unit, where it is cleaned by the supply filters. Then the air flows through the heat exchanger and is directed to the room with the
supply fan. Heat energy of warm extract air is transferred to clean intake fresh air from the outside and warms it up. The air flows are fully
separated while flowing through the heat exchanger. Heat recovery minimizes heat losses, which reduces the cost of space heating in
the cold season.

UNIT OPERATION LOGIC

Supply air

Exhaust air

Supply air

Exhaust air

Intake air

Extract air

Intake air

Extract air

VUT/VUE 300 V2 mini EC

VUT/VUE 300 H2 mini EC

Freeze protection

The heat exchanger freeze protection function of the unit is implemented with a temperature sensor (for units with an A14 control panel)
or a thermostat (for units with an A2 control panel). The temperature sensor is installed in the exhaust air duct downstream of the heat
exchanger. In case of a freezing danger the supply fan is turned off and the heat exchanger is warmed up with warm extract air flow. The
recommended sensor or thermostat operating temperature is +3 °C (exhaust air temperature). If necessary, this setting can be changed
within the software. To set the thermostat temperature set point, set the temperature control knob into a respective position.

UNIT DESIGN

Extract filter

Supply filter

Control unit

Control unit

Supply fan

Supply fan

Heat exchanger

Drain pan

Drain pan

Drain pipe

Drain pipe

Humidity sensor

(option - only for A14 automation)

Humidity sensor

(option - only for A14 automation)

Intake air filter with higher level of filtering

Supply filter
Supply air filter with higher level of filtering

Extract air temperature sensor

(option - only for A14 automation)

Heat exchanger

Extract air temperature sensor

(option - only for A14 automation)

Extract fan

Extract fan

Thermostat

(only for A2 automation)

Thermostat

(only for A2 automation)

Extract filter

VUT/VUE 300 V2 mini EC

VUT/VUE 300 H2 mini EC

«
...
4
5
6
7
8
...
»

Содержание VUE 300 H2 MINI EC A14

























Отзывы:

Нет отзывов

Похожие инструкции для VUE 300 H2 MINI EC A14

Skyline OAH003GDAC

Бренд: Daikin Страницы: 80

Бренд: Rinnai Страницы: 44

Бренд: Daikin Страницы: 40

Бренд: RDZ Страницы: 40

Бренд: RDZ Страницы: 44

Бренд: Trenton Страницы: 12

CLASS UNIT 1000

Бренд: Swegon Страницы: 22

CASA SMART W9 Econo

Бренд: Swegon Страницы: 36

Бренд: Swegon Страницы: 40

Бренд: Swegon Страницы: 60

Бренд: Swegon Страницы: 66

Бренд: Swegon Страницы: 64

BlueBox Tau SKY Hi HP

Бренд: Swegon Страницы: 88

Бренд: Swegon Страницы: 108

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды