background image

3

• 

Do not use damaged equipment or cables 

when connecting the unit to power mains.

• 

Do not operate the unit outside the 

temperature range stated in the user’s 

manual.

• 

Do not operate the unit in aggressive or 

explosive environments.

• 

Do not touch the unit controls with wet 

hands.

• 

Do not carry out the installation and 

maintenance operations with wet hands.

• 

Do not wash the unit with water.

• 

Protect the electric parts of the unit 

against ingress of water.

UNIT MOUNTING AND OPERATION SAFETY PRECAUTIONS

• 

Do not allow children to operate the unit.

• 

Disconnect the unit from power mains prior 

to any technical  maintenance.

• 

Do not store any explosive or highly 

flammable substances in close proximity to 

the unit. 

• 

When the unit generates unusual sounds, 

odour or emits smoke  disconnect it from 

power supply and contact the Seller.

• 

Do not open the unit during operation.

• 

Do not direct the air flow produced by the 

unit towards open flame or ignition sources.

• 

Do not block the air duct when the unit is 

switched on.

• 

In case of continuous operation of the unit 

periodically check the security of mounting.

• 

Do not sit on the unit and avoid placing 

foreign objects on it.

• 

Use the unit only for its intended purpose.

RECYCLE AT THE END OF THE SERVICE LIFE. 

 

DO NOT DISPOSE THE PRODUCT WITH UNSORTED MUNICIPAL TRASH. 

F112EN-02.indd   3

05.10.2015   16:09:55

Содержание TwinFresh Expert





















Отзывы: