background image

3.  Do not let children play with packaging. 
4.  Check the household voltage to ensure it matches the heater’s 

rated specification. 

5.  Check the power cord and plug (purchased separately) 

carefully before using to ensure there is no damage. 

6.  Before working on the electrics, be sure to turn off the power. 

When energizing the unit, be sure your hands are dry to 

prevent electric shock. 

7.  This heater is hot when in use. To avoid burns, do not let bare 

skin touch hot surfaces. Keep combustible materials, such as 

furniture, pillows, bedding, papers, clothes, and curtains at 

least 3 feet (0.9 m) from the front of the heater and keep them 

away from the sides and rear. 

8.  Do not use near or in the immediate vicinity of a bath or 

swimming pool or any wet areas. 

9.  To protect against electric shock, do not immerse cord or plug 

in water or any other liquids. 

10.  Do not insert or allow foreign objects to enter any ventilation 

openings, as this may cause an electric shock, fire or damage 

to the heater. 

11.  Unplug the heater when not in use, if applicable. 
12.  Connect to properly grounded outlets only. 
13.  Always plug heaters directly into a wall outlet/receptacle. 

Never use with an extension cord or relocatable power tap 

(outlet/power strip). 

14.  Do not allow cord to overhang the counter top where it can be 

easily pulled by children. 

15.  Do not put fingers or foreign objects into the grille while in 

operation. 

16.  Do not leave the appliance unattended when in use. 
17.  No liability can be accepted for any damage caused by non-

compliance with these instructions or any other improper use 

or mishandling. 

 

Содержание SUNB2000BL









Отзывы: