Vent-Axia LoWatt T Series Скачать руководство пользователя страница 8

 

REASSEMBLY - ALLOW THE COMPONENTS TO DRY BEFORE REASSEMBLY 

G16 Replace the outdoor grille with the louvres slanting downwards and the Vent-Axia logo at the top grille. 
G17 Align the impeller with the locating pins on the motor shaft. With a sharp push, replace the impeller back 

onto the motor shaft. Ensure that the impeller snaps into position. 

G18 Refit the motor body housing assembly and turn clockwise until the locking catch is engaged. Take care 

not to trap the speed controller connection socket cable (wired version only). 

G19 Release the Power Supply/ Receiver Unit locking catch and lower until the catch engages in the lower 

position. Fix the controller connection socket into position (wired version only). 

G20 Refit the housing ensuring that no internal wires are trapped between the housing and base. 
G21 Engage the two side catches. Tighten the two side catch screws.

 

G22 Replace the indoor grille and secure with the retaining screw at the top of the grille. 
G23 Position the fan on the indoor frame ensuring the socket connector cutout is aligned. Attach the clamps. 

Ensure that the tongues under the clamp heads engage in the slot of the housing.  

G24 (Tighten the clamping screws) G24. 
G25 Place the fan partially into the wall liner and replace the connector socket by pushing positively into 

position. Plug the controller wire into the controller (wired version only). Fix the fan onto the inside liner with 
the louvres slanting upwards using the fixing screws and replace the screw covers. Note: The A’s and B’s 
must match. 

 
RECONNECT THE MAINS SUPPLY AND SWITCH THE UNIT ON. 
 

 
 
 
 

 
 
 
 
 
 
 
 

 
 
 

 
 
 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

G4a

G1 G2

G3 

G4b 

G5 

G6

G7

G9 

G8 

G10 

Содержание LoWatt T Series











Отзывы: