MA-AL-T75E-01-03 Manual TUL375EN eng rev3
Rev.3 Page 2 of 4
Low battery:
control tension lower than 22 Vdc
Battery ok:
tension included between 22 Vdc and 28,5 Vdc
Overcharged battery:
tension over 28,5 Vdc
Mains:
presence of line tension 230 Vac
Failure
:
Led of general failure, it activates in case of:
Absence of 230 Vac mains
Faulty fuse
Loss of battery charge
Low battery
Overcharged battery
Disconnected battery
Battery resistance > 1 ohm
The power supply has been certified using YUASA NP 17-12 batteries
Security Instructions
1.
For mains input and DC o alarms, use separate holes on the bottom of the box to pass the cables. Furthermore, the material of the
joint pipe/box must have a flammability class V-1 or better
2.
The relay contact “GUASTO” and “RETE RIT ” must be connected only to circuits operating with SELV tension.
3.
For AC supplying, provide a 6 A protection bi-pole magneto-dynamic switch, easy to access
4.
The wires must have a section of 1,5 mm and be equipped with adequate buttonholes where they are subject to pressure contact.
5.
The installation of the power supply must be carried out by qualified personnel aware of the security norms EN60950 and concerning power
supplies CEI-64-8.
IMPORTANT: In case of mains failure and general anomaly condition, a technical intervention should be carried out within 48 hours to
avoid the complete discharge of the battery.
INSTALLATION
MECHANICAL MOUNTING
This device has to be mounted on vertical stable walls, suitable to support the power supply, by means of 4 6 mm screws, for spacers and screws on
the 4 holes on the bottom of the box. The battery must be fixed using the strap given within.
ELECTRICAL CONNECTION
Connect the power supply unit to the mains 230 Vac by use of a differential magneto-thermic bipolar 6 A. switch (minimum distance between contacts
3 mm) aimed to protect the line against possible short circuit and operator against current leakage.
IMPORTANT: use different cables-passes and pipes for ac supplying input (mains 230 Vac) and dc o alarms (SELV)
– see pict. 2
The minimum section recommended for ground connection is 1,5 mm.
For connections refer to pictures 1 and pict. 2. In these pictures the following important steps are shown:
Output Terminals (Power supply unit)
Output terminal board (power supply)
BAT +
Positive pole of the battery
OUT 2 +
Positive output towards charge 2
BAT -
Negative pole of the battery
OUT 2 -
Negative output towards charge 2
OUT1 +
Positive output towards charge 1
OUT 3 +
Positive output towards charge 3
OUT1 -
Negative output towards charge 1
OUT 3 -
Negative output towards charge 3
Terminal board Alternated Supplying
L
connection to line (230 Vac)
Protection ground connection N connection to neutral
Checks and Adjustments
Controls are shown Below (P1 and P2) are adjusted at factory and
must in no way be altered by the operator.
Tampering of these controls automatically means the lost of the warranty.
P1 - Potentiometer for adjustment of the output tension
P2 - Potentiometer for adjustment of the output current limit.
FRONT PANEL SIGNALS
Indications on the front panel (located on the door of the power supply)
Mechanical Specifications
Size in mm.
width 310 ; height 373 ; depth 170
Weight
9,5 Kg
Environmental Specifications
Operating temperature
from -5 °C to +40 °C
Humidity
from 5% to 93% ±
2 %
cooling
air cooling
Installation site
sheltered from atmospheric agents
FUSES
F1
Fuse of the 230 Vac supplying input (T3,15 AL 250V)
F5
Fuse related to output OUT 2 (T3,15 AL 250 V)
F3
Battery fuse (T6,3 AL 250 V)
F6
Fuse related to output OUT 3 (T3,15 AL 250 V)
F4
Fuse related to output OUT 1 (T3,15 AL 250 V)
F8
Fuse of protection over-tension (T6,3 AL 250 V)
Low battery Battery OK Overcharged Mains Failure
battery
