Velux CLI U12 SD0F1110 NG B/U Скачать руководство пользователя

Страница: 50 / 56

50 – Part 7: Troubleshooting

Part 7: Troubleshooting

Nature of trouble

Possible cause

Service

No hot water.

Improper wiring.

Check controller and tank wiring.

No Power – blown
fuse or circuit breaker
tripped.

a. Shorted wiring.

Replace or repair.

b. Circuit overloaded.

Provide adequate circuit or reduce
load.

c. Improper wiring.

Rewire per wiring diagram.

d. Grounded element

or thermostat.

Replace.

Manual reset limit
(ECO) open.
Refer to “Operation”
Section.

a. Thermostat

defective.

Replace thermostat.

b. Thermostat out of

calibration.

Lower setting or replace.

c. Heat build-up due

to loose wires.

Tighten wire connections.

d. Defective Limit

(ECO).

Replace.

Solar system controller incorrectly installed.

Check installation.

Defective storage tank element.

Replace element.

Leaking plumbing or open hot water faucet(s).

Make sure all faucet(s) are closed and
check water meter.

Not enough hot water.

System undersized.

Reduce rate of hot water use.

Defective element.

Check amperage, replace element.

Defective thermostat or wired incorrectly.

Check wiring or replace.

Solar system controller incorrectly installed.

Check Installation.

Leaking plumbing or open hot water faucet(s).

Make sure all faucet(s) are closed and
check water meter.

Water too hot or not hot
enough.

Thermostat setting too high or low.

Change setting as required.

Thermostat out of calibration.

Replace.

Solar system incorrectly installed.

Check installation.

Grounded element.

Replace.

Noisy tank heating element.

Scale build-up on element.

Remove and clean.

Rattling noise in tank during
periods of water usage.

Tank internal heat trap fittings in operation.

None. Normal for heat trap fittings.

Water pressure too high.

Check and call local utility if necessary.

Scale build-up inside storage tank.

Drain and flush tank.

CAUTION

For your safety, do not attempt repair of electrical wiring, thermostat, heating element or other operating controls. Refer
repairs to qualified service personnel.

Содержание CLI U12 SD0F1110 NG B/U

























































Результаты поиска

Содержание CLI U12 SD0F1110 NG B/U

Отзывы:

Похожие инструкции для CLI U12 SD0F1110 NG B/U

Бренды по названию

Популярные бренды

Velux CLI U12 SD0F1110 NG B/U, Установка, эксплуатация и обслуживание

Результаты поиска

Содержание CLI U12 SD0F1110 NG B/U

Отзывы:

Похожие инструкции для CLI U12 SD0F1110 NG B/U

Бренды по названию

Популярные бренды