Velleman-Kit HIGH-Q K8040 Скачать руководство пользователя | Manualshive

Страница: 18 / 24

background image

18

Solder a 15cm (2.5mm) wire to the LS connectors. Black = negative, Red=
positive, use a shrink tube to isolate the connection.

Solder a spade terminal to the other end, do not forget the terminal isolation.

Mount (insert) the mains connector onto the rear panel. Insert a 2A fuse into
the connector (there is also room for a spare fuse).

28. Final assembly and connection

Final assembly

15cm

«
...
16
17
18
19
20
...
»

Содержание HIGH-Q K8040

























Отзывы:

Нет отзывов

Похожие инструкции для HIGH-Q K8040

Бренд: Octave Страницы: 23

Бренд: NAD Страницы: 20

Бренд: NAD Страницы: 8

Бренд: XINDAK Страницы: 10

Бренд: Channel Master Страницы: 2

Бренд: McIntosh Страницы: 55

Бренд: MTX Страницы: 14

Бренд: dB Страницы: 20

Бренд: Pyle Страницы: 1

Бренд: Majorcom: Страницы: 8

Бренд: Soundavo Страницы: 12

Бренд: Labgear Страницы: 2

MOON Evolution MC-8

Бренд: Simaudio Страницы: 11

Ironheat IRT30-112

Бренд: Laney Страницы: 16

Бренд: Sonic Farm Страницы: 8

Бренд: Toa Страницы: 12

Бренд: Xtant Страницы: 13

Бренд: Rotel Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды