VELIT 4000P Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 23

background image

4Kw Air Fuel Heaters

5

3.2.2

The sealing between the heater and the mounting surface must
be intact.

During installation, the sealing gasket provided by the
manufacturer must be used, and the mounting surface must be
flat.

Four M6 nuts provided by the manufacturer shall be used for
securing the unit at 6-7Nm. Note: When the heater is
reinstalled, the gasket must be replaced.

«
...
6
7
8
9
10
...
»

Содержание 4000P
























Отзывы:

Нет отзывов

Похожие инструкции для 4000P

Бренд: Marta Страницы: 12

Бренд: A.O. Smith Страницы: 8

Platinum GHOR900

Бренд: Goldair Страницы: 16

Бренд: Echelon Страницы: 8

Бренд: Sure Heat Страницы: 12

Бренд: Pakole Страницы: 30

Elztrip EZ300 Series

Бренд: Frico Страницы: 12

Бренд: GE Страницы: 24

Бренд: Luxlink Страницы: 2

Бренд: DèLonghi Страницы: 7

Бренд: Jaga Страницы: 68

Бренд: DeLonghi Страницы: 15

Бренд: REMKO Страницы: 16

Бренд: Convair Страницы: 8

Бренд: Frico Страницы: 14

HTS.1.PUR.24.BL

Бренд: Heatscope Страницы: 14

Бренд: Reznor Страницы: 32

AirLink 9900 NXP

Бренд: RKI Instruments Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды