background image

33

9 Supplement

VEGASWING 61 • - transistor (NPN/PNP)

29225-EN-161125

Electromechanical data - version IP 66/IP 67 and IP 66/IP 68; 0.2 bar

Cable entry/plug

2)

 

Ʋ Single chamber housing

 

– 1 x cable gland M20 x 1.5 (cable: ø 5 … 9 mm), 1 x 

blind plug M20 x 1.5

or:

 

– 1 x closing cap ½ NPT, 1 x blind plug ½ NPT

or:

 

– 1␣x plug (depending on the version), 1␣x blind stopper 

M20␣x␣1.5

Screw terminals

for wire cross-section up to 1.5 mm² (AWG 16)

Electromechanical data - version IP 66/IP 68 (1 bar)

Cable entry

 

Ʋ Single chamber housing

 

– 1 x IP 68 cable gland M20 x 1.5; 1 x blind plug 

M20 x 1.5

or:

 

– 1 x closing cap ½ NPT, 1 x blind plug ½ NPT

Connection cable

 

Ʋ Wire cross-section

> 0.5 mm² (AWG 20)

 

Ʋ Wire resistance

< 0.036 Ω/m (0.011 Ω/ft)

 

Ʋ Tensile strength

< 1200 N (270 lbf)

 

Ʋ Standard length

5 m (16.4 ft)

 

Ʋ Max. length

1000 m (3280 ft)

 

Ʋ Min. bending radius

25 mm (0.984 in) with 25 °C (77 °F)

 

Ʋ Diameter approx.

8 mm (0.315 in)

 

Ʋ Colour - standard PE

Black

 

Ʋ Colour - standard PUR

Blue

 

Ʋ Colour - Ex-version

Blue

Adjustment elements

Mode switch

 

Ʋ A

Max. detection or overflow/overfill protection

 

Ʋ B

Min. detection or dry run protection

Density changeover switch

 

Ʋ ≥ 0.5 g/cm³

0.5 … 2.5 g/cm³ (0.018 … 0.09 lbs/in³)

 

Ʋ ≥ 0.7 g/cm³

0.7 … 2.5 g/cm³ (0.025 … 0.09 lbs/in³)

Voltage supply

Operating voltage

10 … 55 V DC

Power consumption

max. 0.5 W

2)

  Depending on the version M12 x 1, according to ISO 4400, Harting, 7/8" FF.

Содержание VEGASWING 61









































Отзывы: