background image

VEGAPULS 56K

61

ration/Sensors“

In this menu window, the present adjustment
(database) with the data and time of the last
system configuration is shown in the yellow
window cut-out.
When you click to the series number of the
sensor of which you want to take over the
adjustments, you can transfer these sensor
adjustments to the presently connected sensor

Set-up

with "

Restore to“.

6.3 Adjustment with adjustment

module MINICOM

Like with the PC, the sensor can be also
adjusted with the small, detachable adjust-
ment module MINICOM. The adjustment
module is hence plugged into the sensor or
into the external indicating instrument (option-
ally).

For the adjustment with the adjustment module
all adjustment options are available like with
the PC and the adjustment program VVO.
However the adjustment with MINICOM is
different.

You carry out all adjustment steps with the 6
keys of the adjustment module. A small dis-

play gives beside the meas. value in short
words the message on the menu point or the
value of a menu adjustment.

The information volume of the small display
however cannot be compared with the adjust-

-

+

ESC

OK

2

4

Tank 1
m (d)
12.345

-

+

ESC

OK

Tank 1
m (d)
12.345

4 ... 20 mA

Содержание VEGAPULS 56K









































































Отзывы: