background image

21

5 Connecting to power supply

VEGAPULS 11 • Two-wire 4 … 20 mA

58350-EN-221027

You have to remove this plug before electrical connection.

NPT thread

In the case of instrument housings with self-sealing NPT threads, it 

is not possible to have the cable entry screwed in at the factory. The 

cable gland is therefore covered with a red dust protection cap as 

transport protection.

Note:

To ensure the housing protection class, you must replace this protec-

tive cap with an approved NPT cable gland before setup.

Note:

Do not use grease when screwing in the NPT cable gland or a conduit 

steel pipe.
Maximum torque see chapter " 

Technical data

". 

5.2 Connecting

The voltage supply and signal output are connected via the spring-

loaded terminals in the housing.

Proceed as follows:
1.  Unscrew the housing lid
2.  If a display and adjustment module is installed, remove it
3.  Loosen compression nut of the cable gland and remove blind 

plug

4.  Remove approx. 10 cm (4 in) of the cable mantle, strip approx. 

1 cm (0.4 in) of insulation from the ends of the individual wires

5.  Insert the cable into the sensor through the cable entry

Connection technology

Connection procedure

Содержание VEGAPULS 11

























































Отзывы: