background image

28

39089-US-210509

Operation

Radiation Survey after Installation

1.

Complete the survey sheets with measurements at 30 cm (12") omni-
directionally to record the radiation pattern.

2.

Survey in the closed (OFF) position and then in the open (ON) position.

3.

Do an occupancy evaluation to determine the dose personnel might 
receive. There are two categories, each with a different limit:

Members of the general public can receive 20 mSv/hr (2 mrem/hr), not to 
exceed 1,000 µSv/yr  (100 mrem/year). These numbers include only 
individuals who are in the area infrequently and have no assigned 
reason for exposure.

Occupationally-exposed individuals can receive 50,000 mSv (5,000 
mrem) per year with no specified rate limit. This number includes anyone 
whose assigned duties require his presence in the vicinity of the source 
holder. Complete the evaluation to determine if the limit of 5,000 mSv 
(500  mrem) per year, which would require monitoring, is potentially 
reachable.

4.

Decide if additional shielding is required to prohibit members of the general 
public from receiving radiation doses greater than 20 mSv/hr (2 mrem/hr).

5.

Notify appropriate personnel of the presence of radioactive materials and 
precautions that they must take to minimize exposure.

6.

If there are radiation fields above 20 mSv/hr (2 mrem/hr) present on the 
detector side, notify the RSO (Radiation Safety Officer) of the problem.

7.

Restrict the area, if required.

Shutter Operation Test

On applicable source holders, the shutter operation test verifies that the shutter 
is functioning.

If the shutter does not work correctly, see the 

Radiation Safety 

Manual Emergency Guidelines

.

!

NOTE

Содержание SHLG

















































Отзывы: