Vega B 53-19 Скачать руководство пользователя страница 7

7

3 Product description

B 53-19 • For the signal cable of conductive probes

40490-EN-220516

carrier rail according to EN 50 022/EN 50 035 in the switching cabinet 

or in a metal or plastic housing close to the sensor.

Depending on the version, different combinations of protective ele-

ments for voltage limitation are used. Typical protective elements 

are suppressor diodes (diodes with special characterstics), varistors 

(voltage-dependent resistors) as well as overvoltage arresters (gas 

arresters).
As soon as the voltage increases to the response voltage of the 

protective element, the element becomes conductive and the energy 

is discharged to ground. After the overvoltage has subsided, the 

protective element returns to its high-impedance state and thus has 

no influence on the supply or signal circuit.

3.3  Packaging, transport and storage

Your instrument was protected by packaging during transport. Its 

capacity to handle normal loads during transport is assured by a test 

based on ISO 4180.
The packaging of standard instruments consists of environment-

friendly, recyclable cardboard. For special versions, PE foam or PE 

foil is also used. Dispose of the packaging material via specialised 

recycling companies.

Transport must be carried out in due consideration of the notes on the 

transport packaging. Nonobservance of these instructions can cause 

damage to the device.

The delivery must be checked for completeness and possible transit 

damage immediately at receipt. Ascertained transit damage or con-

cealed defects must be appropriately dealt with.

Up to the time of installation, the packages must be left closed and 

stored according to the orientation and storage markings on the 

outside.
Unless otherwise indicated, the packages must be stored only under 

the following conditions:

• 

Not in the open

• 

Dry and dust free

• 

Not exposed to corrosive media

• 

Protected against solar radiation

• 

Avoiding mechanical shock and vibration

• 

Storage and transport temperature see chapter " 

Supplement - 

Technical data - Ambient conditions

• 

Relative moisture 20 … 85 %

With instrument weights of more than 18 kg (39.68 lbs) suitable and 

approved equipment must be used for lifting and carrying.

Functional principle

Packaging

Transport

Transport inspection

Storage

Storage and transport 

temperature

Lifting and carrying

Содержание B 53-19





















Отзывы: