VeEX VePAL TX300M Скачать руководство пользователя страница 212

Страница: 212 / 421

11.2 E3 Pulse Mask

This function captures and analyzes E3 (34.368Mbps) pulse shape. The purpose of maintaining the correct pulse shape is to

reduce inter-symbol interference – if the logic 1s and 0s cannot be detected by the receiver correctly, bit and code errors will

result.

The pulse amplitude and overall shape are superimposed and compared with ITU-T G.703 pulse conformance template.

Telecommunications signals require specific load impedance for pulse mask compliance testing to be accurate. When high

frequency pulses are transmitted down a transmission line, a portion of the pulse will be reflected when and wherever it

encounters an impedance mismatch. The reflection is proportional to the impedance mismatch (i.e., the greater the mismatch, the

greater the reflection of the pulse).

E3 Pulse Mask

Go back to top

Go back to TOC

11.3 E1 APS Testing

This function measures the Automatic Protection Switching (APS) limits of the network. APS applies the Multiple E1 Links and

enables network elements to re-route traffic to a backup circuit in the event of network failure or problems.

TX300S_e-manual_D07-00-064P_RevA00

Содержание VePAL TX300M






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды

VeEX VePAL TX300M, Руководство пользователя

Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды