VeEX VePAL TX300 Скачать руководство пользователя

Страница: 406 / 421

17.2 CPRI Testing

QoS Requirements

Bit Error Ratio:

The interface shall provide U-plane and C&M plane data transmission (on Layer 1) with a maximum bit error ratio of
10

-12

Maximum Delay:

In order to support efficient implementation of UTRA-FDD inner loop power control, the absolute round trip time for

U-plane data (IQ data) on the interface, excluding the round trip group delay on the transmission medium (i.e.,

excluding the cable length), shall not exceed the following maximum value of 5 µs.

Test Areas

Tests for CPRI Transport link should focus on verifying that BER requirements are met by performing the following tests:

Test in Layer 1 unframed mode to verify CPRI physical layer with 8b/10b line coding (see CPRI protocol stack)

Test at full line rate

Test Ports

Go back to top

Go back to TOC

TX300/e_e-manual_D07-00-033P_RevG00

Содержание VePAL TX300






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300

Отзывы:

Похожие инструкции для VePAL TX300

Бренды по названию

Популярные бренды

VeEX VePAL TX300, Руководство пользователя

Результаты поиска

Содержание VePAL TX300

Отзывы:

Похожие инструкции для VePAL TX300

Бренды по названию

Популярные бренды